background image

BEFORE INSTALLING THE  BW-1600

• DO read through this installation manual.
• DO NOT install the alarm brain in an engine compartment.
• The alarm may arm itself when power is first connected.This is a normal condition.

ITEMS SUPPLIED WITH THE  BW-1600

BW-1602

Receiver and Control Module

BW-260P

Valet/Override Switch

BW-385

2-Button, Code Learning 

BW-180P

LED Status Indicator

Transmitters (2)

BW-12016

Wiring Harness, Fuseholder, & Fuse

MTS-20W

Six-tone, soft chirp, 120 dB Siren

BW-296P

Dual Zone Electronic Shock Sensor

BW-12016DL

Door Lock Harness

OPTIONAL ACCESSORIES

Radar Field Sensor.........................................

MAS-2

Backup Battery .......................................................

BW500

Window Rollup.............................................

WRM-2

Remote Starting.................................................

RAS-101

Power Door Lock........................................

PDL-50

Trunk Release ........................................................

TR-100

Relay......................................................................

SPDT

Relay Socket ........................................................

BRS-003

5-wire Door Lock relay & socket .

BRS-008PR

Glass Sensor .......................................................

BWS-200

(+) Door Lock Inverter.............................

BW-345

SPECIFICATIONS

Operating voltage ...............+12 VDC Neg. Ground
Code Learning ......................................3 Codes Max.
Current consumption .........5 mA (max) disarmed.
Siren output drive ......................................3 Amperes
Automatic reset........................................60 seconds.
Door Lock/Unlock Output ...................(-) 500 mA.
Channel 2 Output Drive ........(-) 500 mA variable.

Remote control transmit freq.............................310 mHz.
Passive arming delay ............................30 Seconds approx.
Auxiliary output drive..........................250 mA maximum.
Flashing output drive ............................10 Amp maximum.
Trigger inputs..............................................1) Neg. pnswtch.
1) Pos. pnswtch. 1) Neg. sensor or aux. pnswtch.

I N S T A L L A T I O N   M A N U A L

Please read this Black Widow manual carefully before attempting to install this system.

B

L

A

C

K

W

I

D

O

W

I N S T A L L A T I O N   M A N U A L

Summary of Contents for BW-1600








Reviews: