Charging
Balancing
Charging
complete
Power
connected
Charger LED codes
Charge the Flight Battery (~75 min)
Install the propellers
Power Up
1
2
6
7
3
4
5
8
9
10
11
CAUTION:
All instructions and warnings must be followed exactly. Mishandling
of Li-Po batteries can result in a fi re, personal injury and/or property damage.
16 ft
(5 m)
Front
Pilot location
Home position
Placement at startup
SAFE Circle
™
CAUTION:
Starting the motors sets the home location. The quadcopter
must be approximately 16 feet (5 meters) from where the pilot will
stand during fl ight, pointing away from the pilot. If the aircraft is pointed in any
other direction, the
SAFE Circle™
feature will not function as expected and may
result in personal injury or damage to property. Once the aircraft’s motors are
started, do not change your position.
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
M A N U A L
Extend the GPS Mast
Install the Flight Battery
Install Your Camera
• Slide the fully charged battery in until it locks.
• Remove the battery by pressing the locking tab and
sliding the battery to the rear of the quadcopter.
12a
12b
QUADCOPTER WITH ST10+ PERSONAL GROUND STATION AND GoPro® COMPATIBLE GPH4 3-AXIS GIMBAL
• The props and motor pods have a letter code, either
“A”
or
“B”
molded in. Match the
“A”
props to the
“A”
motor pods and the
“B”
props to the
“B”
motor pods.
• The
“A”
props thread on counter-clockwise.
• The
“B”
props thread on clockwise.
• Tighten the props only fi nger tight. DO NOT overtighten.
A
A
A
B
B
B
CAUTION:
The GoPro
®
Wi-Fi will interfere
with the quadcopter receiver and may
cause a loss of signal and crash. Follow the camera
instructions to turn the Wi-Fi off before attempting
to power on the quadcopter.
Crash damage is not
covered under warranty.
Connect the USB cable from the gimbal to
your camera USB port.
Install the camera into the gimbal by rotating
the mount as shown.
Slide the camera into the camera mount until
it stops against the front of the mount.
Thread the retaining screw into the mount
until it is snug against the camera. Do not
overtighten.
The included GPH4 3-axis gimbal and MK58 video
transmitter are compatible with GoPro
®
3 and 4 cameras.
CAUTION:
NEVER attempt
to fl y without extending the
GPS mast.
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
Install the 3-axis Gimbal
Slide the
gimbal on the
mount rails until it
locks.
Connect the
wiring har-
ness to the plug on
the bottom of the
quadcopter.
Connect the
2.5mm jack
from the gimbal to
the port in the MK58
video transmitter.
To remove the
gimbal, press the tab
at the front of the mount and slide the gimbal
forward.
b
a
c
d
Motor Start
Motor Stop
Hold 3 seconds
Hold until the motors stop
NOTICE:
Do not press the Motor Stop button
while the aircraft is airborne. The motors could
stop, causing the aircraft to crash.
WARNING:
Stopping the motors while the
quadcopter is still in fl ight will cause the
quadcopter to crash. Crash damage is not covered
under warranty.
• A green LED cycles around the motor
pods counter-clockwise until GPS is
acquired
• Once GPS is acquired, the front LEDs
are white and the rear are green
• Intended for the beginner pilot
• Maximum distance of 100 m from
the pilot
• A purple LED cycles around the motor
pods counter-clockwise until GPS is
acquired
• Once GPS is acquired, the front LEDs
are white and the rear are purple
• Intended for the intermediate pilot
• Maximum distance of 100 m from
the pilot
NOTICE:
If the Chroma
™
quadcopter loses GPS signal while fl ying in either Smart or AP Mode, the LEDs will fl ash rapidly for 2 seconds and then
once every second. The quadcopter will default to a stable fl ight mode with similar control response as AP Mode. Return Home will not function.
Please familiarize yourself with the controls in AP Mode to ensure a safe return of the quadcopter in the event of GPS signal loss.
For best results while using Smart Mode, it is recommended that the
pilot always turn to face the quadcopter while fl ying.
Understanding the Flight Modes
Smart Mode
AP Mode
Pilot location
Right transmitter stick
Stick commands move
the Chroma
™
quadcopter
relative to the pilot location
Stick commands move
the Chroma
™
quadcopter
relative to its orientation
Right transmitter stick
Front
=
=
Away from
the pilot
Toward
the pilot
For information on additional fl ight modes, including “Follow Me,” see the online video at
www.KnowChroma.com.
Left transmitter stick
13
Throttle control
Flying and Landing
After Your Flight
Controlling the Camera Gimbal
14
16
15
NOTICE:
If you begin to lose control, release the control sticks and the
model will self-level.
NOTICE:
Return home will only function if the quadcopter has GPS lock.
Pay close attention to the LEDs while fl ying. If at any time the LEDs indicate the fl ight
battery voltage is low, as shown in the LED reference guide, land the quadcopter
immediately and charge the fl ight battery.
Climb
Descend
To land, you may either slowly lower the left transmitter
stick to descend and land, stopping the motors as
shown in
step 12b:
• To maintain the current
altitude, allow the left
transmitter stick to return
to center.
or you may select
“Return Home”
on the top right switch on your transmitter:
Solid red
The quadcopter will return to the start position, land and stop the motors. You may
cancel the return to home function by switching back to Smart or AP Mode on the
top right switch on your transmitter.
e
f
d
c
b
a
e
f
d
c
b
a
The buttons on the top of the ST-10+ have no function.
Use the Camera Tilt Slider to adjust
the vertical angle of the camera
gimbal.
e
f
d
c
b
a
Camera Tilt Slider
For further information on controlling the 3-axis gimbal
with the ST-10 Ground Station, see the online video at
www.KnowChroma.com.
Install and Charge the ST-10+ Transmitter Battery
Insert the LiPo battery into
the ST-10+ transmitter.
Connect the battery lead
to the transmitter noting
the correct polarity.
Close the battery compartment.
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
Connect the USB
cable to an appropriate
USB power source and to the
charge port of the transmitter.
The screen will show a charging
battery icon. Disconnect the
USB cable when the onscreen
battery icon shows full capacity.
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
2
Place the quadcopter
outdoors on a fl at,
level surface.
Set the top right
transmitter switch
to Smart.
Power on the
transmitter.
Power on the
quadcopter.
The LEDs will show
green, rotating counter-
clockwise around the motor pods
while the quadcopter acquires a
GPS signal. The front LEDs will
show white and the rear will show
green when the quadcopter is
ready for fl ight.
Perform the compass
calibration as shown in the
video at
www.KnowChroma.com.
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
Link the Camera to
the ST-10+ via Wi-Fi
After the Chroma powers on, power on your camera.
The MK58 video transmitter will begin transmitting
video.
To link the MK58 transmitter signal to the ST10+:
Select Flight Settings from the main menu on
the ST-10+.
Select the Bind option.
Under Camera, select the LK58MINI_71000
network (LK58MINI_******).
Touch the Password line on the screen and enter
the password “12345678” on the touchscreen.
Select OK.
The ST-10+ will indicate a successful
connection. Select OK.
Return to the Main Menu.
The live video feed is now visible on the ST-10+ display.
Double tap on the image to expand the video to fi ll the
display. Double tap again to return to the main menu
with live video.
This aircraft is not compatible with Spektrum
™
DSM
®
, DSM2
®
or DSMX
®
technology.
b
a
c
d
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
d
c
b
a
e
f
g
d
c
b
a
NOTICE:
Refer to the
“Charging Warnings”
on the back of this page.
b
c
