BN Products DBC-16H Manual Download | Manualshive

Page: 1 / 12

background image

3450 Sabin Brown Road • Wickenburg, AZ 85390

(800) 992-3833 • (928) 684-2813 • mail@bnproducts.com

BN PRODUCTS-USA, LLC.

DBC-16H_TM_16

Page | 1

DBC-16H

Portable Electric #5 (16mm) Combination

Rebar Bender and Rebar Cutter

Please note:

This tool is rated for #5 (16mm) Grade 60 Rebar Only

. Do not try to bend

or cut material larger in size or rebar harder than grade 60 or you will cause tool damage

or machine failure.

1
2
3
...
»

Summary of Contents for DBC-16H













Reviews:

No comments

Related manuals for DBC-16H

Hydralok HCL Mobile

Brand: Interpump Pages: 17

Brand: Brother Pages: 72

Brand: Makita Pages: 40

Brand: SIZZIX Pages: 6

Brand: Stiga Pages: 47

Brand: Logan Graphic Products Pages: 24

Brand: FARM-MAXX Pages: 7

Brand: Lux Tools Pages: 26

Brand: Proxxon Pages: 54

Brand: IQ Power Tools Pages: 5

Brand: Mafell Pages: 106

Brand: Oleo-Mac Pages: 76

Brand: Partner Pages: 11

Brand: Zipper Mowers Pages: 50

Brand: Zipper Mowers Pages: 28

Brand: Far Tools Pages: 42

Brand: Far Tools Pages: 74

Brand: Arkiplot Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands