background image

 

 

SX-16 Nightsun

®

 Searchlight System 

 

Maintenance Manual 

Document 031734-1/Revision A  

031734-1 Revision B 

 

January 27, 2014

 

  

 

  

 

1.0  OVERVIEW OF THE SX-16 NIGHTSUN

®

 

1.1 

Description and Features 

The SX-16 Nightsun

®

 Searchlight System (called the SX-16 Nightsun

®

 or simply the Searchlight from 

this point forward in the manual) is a versatile, mobile, high-intensity light source. It can be mounted 
on fixed wing aircraft, helicopters, and water craft. When properly installed and operated, it can flood 
an area with light from a safe distance. 

 

The Searchlight uses an air cooled, high-intensity  xenon arc lamp. It emits light that is the 
same color as daylight, starts rapidly, and can be operated continuously or started and 
stopped to meet operational requirements. 

 

The Gimbal assembly that supports the Searchlight enables users to aim the Searchlight 
beam at various positions with respect to Azimuth  (horizontal directions) andElevation 
(vertical directions). 

 

The SX-16 Nightsun

®

 responds to directional commands from a hand operated Control Box. 

1.2 

 About This Manual 

This manual provides the following information: (1) information to help you to set up the SX-16 
Nightsun

®

  components and (2) information to help you maintain and troubleshoot the SX-16 

Nightsun

®

. A separate manual provides information about operation. 

1.3 

Read, Obey, and Keep Instructions 

To ensure the safety of people and equipment, it is important to read and obey all instructions and 
safety warnings contained in this document and posted on the equipment before you attempt to 
operate, maintain, or troubleshoot the SX-16 Nightsun

®

. Keep this document for reference. 

 

1.4 

Applicable Documents 

032431, SX-16 QUICK CONNECT CABLING DIAGRAM 
032436, SX-16 QUICK CONNECT SYSTEM SCHEMATIC 
032427, STANDARD SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE DRAWING 
032428, LONGER ARM SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE DRAWING 
032429, IFCO SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE DRAWING 
034187, SX-16 IFCO QUICK CONNECT CABLING DIAGRAM 
032436, SX-16 QUICK CONNECT SYSTEM SCHEMATIC 
033899, IFCO SPECTROLINK SX-16 QUICK CONNECT SYSTEM SCHEMATIC 
034030, IFCO SPECTROLINK SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE 
DRAWING 
033584, SX-16 IFCO SPECTROLINK QUICK CONNECT CABLING DIAGRAM 
032222, STANDARD HARD WIRED SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE 
DRAWING 
020720, HARD WIRED SX-16 SYSTEM SCHEMATIC 
031661, HARD WIRED SX-16 CABLING DIAGRAM 
034029, SPECTROLINK SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE DRAWING 
032229, HARD  WIRED IFCO SX-16 SEARCHLIGHT AND GIMBAL SYSTEM ENVELOPE 
DRAWING 

 

 

 

 

 

Source:  Spectrolab, Inc. 

1

 

The document reference is online, please check the correspondence between the online documentation and the printed version.

Summary of Contents for SPECTROLAB SX-16 Nightsun



























Reviews: