background image

RIP-12 SHUTTING OFF 

1)

 

Shut off the mains power supply 220 V. 

2)

 

Detach the battery. 

3)

 

Remove the fuse F1. 

4)

 

Disconnect the load circuit. 

MAINTENANCE 

The maintenance of RIP-12 is to be carried out annually. The maintaining operations include: 
1)

 

RIP-12 visual inspection to discover mechanical injures and to clean any dirt or dust if presented. 

2)

 

Measuring the power output parameters and checking them to be in conformance with items of 
SPECIFICATION. 

3)

 

LED and sound indication testing to meet the requirements of Table above. 

4)

 

Proper RIP-12 firmly attaching, and contact tightening, and wire integrity inspection. 

WARRANTY 

Manufacturer warrants RIP-12 Uninterrupted Power Supply to be free from defects and to operate in 

conformance with specification under normal transportation, mounting and maintenance for 18 months since putting 
it into operation, but no more than for 24 month since acceptance date (see below). 

In the event of in-warranty failure the failed RIP-12 should be brought back to the manufacturer supplied with 

its damage certificate describing the defect and its acceptance certificate to validate the warranty status. Send your 
complaints to the manufacturer at the following address: 

ZAO NVP BOLID 
#4, Pionerskaya street, Korolyov, Moscow Region, Russia, 141070 
Tel./fax +7 495 777-40-20, +7 495 516-93-72. 

E-mail: 

info@bolid.ru

, Web-site: 

www.bolid.com

 

ACCEPTANCE CERTIFICATE 

RIP-12 Uninterrupted Power Supply model 02 

 

 

    Product Designation                                                                   Serial Number 

Produced, tested by quality control department in compliance with state standards and specifications, packed by 

NVP BOLID Company and qualified as deliverable. 

Q.C. 
STAMP                   _____________________                             ____________________________ 
                                            Name                                                                Date of Acceptance 

 
 

UNINTERRUPTED POWER SUPPLY 

RIP-12 model 02 

INSTRUCTION MANUAL 

 

GENERAL

 

Uninterrupted Power Supply RIP-12 model 02 (referred to as RIP-12 below) is designed to provide the electric 

power to various fire and intruder detectors, as long as control and indication equipment suited for uninterrupted 12 
VDC. 

RIP-12 is round-the-clock operating device with defined output parameters, sealed backup battery being tested 

and charged automatically. PIR-12 provides battery shutting off from load circuit in order to avoid its unacceptable 
discharge. 

RIP-12 is equipped with light and audible indication of its current status, i.e. normal or no voltage, battery 

charge, output short failure or overload, battery missing or shutting down when discharged. 

When operated, RIP-12 should be protected against atmospheric fallout and mechanical damage. 

SPECIFICATION 

AC Input Voltage Range 

– from 187 to 242 VAC @ 50 Hz 

Backup Power Supply 

– battery «Delta» DTM1207 12 V @ 7 Ahr or analogous 

Output Voltage Range 

– 13.6 

±

 0.6 VDC at both AC and charged battery powering; 

 

– 11.0 

±

 0.5 VDC min provided the battery is discharged 

Load Current Rating 

– 2.0 

А

 

Maximum Load Current 

– 3.0 

А

 within 10 minutes or 5 

А

 within 2 minutes at both mains 

and battery powering, once an hour minimum 

Input Current Consumption 

– 0.3 

А

 maximum for rating load 

Ripple (mVp-p)×2 

– 20 mV maximum at rating load current 

Battery Low Shutdown 

– 10.2

±

0.6 VDC 

On Battery Run-Time 

– at least 5 hours for 1 A load current, increasing proportionally to 

load reduction 

Ingress Protection Rating 

– IP20 

Power-Up Operation Readiness 

– 6 seconds maximum 

Operating Temperature Range 

– from –10

°

C to +40

°

Overall Dimensions 

– 255

х

310

х

95 mm 

RIP With Battery Weight 

– 6.5 kg maximum 

Typical Lifetime 

– 8 years, the battery being to be replaced once every 5 year 

RIP-12 provides protection against short circuit failure along with automatically recovering of output voltage 

after short failure disappearing while powered from mains and backup battery. 

RIP-12 is equipped with open collector transistor output functioning as contact closure device. It is opened 

when AC line fails and RIP-12 is operating in battery mode, or in case of a short load circuit failure, so it can be 
used for remote signaling of RIP electric troubles. The maximum output permissible voltage and commutation current 
are 30 V and 100 mA respectively. 

DELIVERY SET 

Uninterrupted Power Supply RIP-12 model 02 

 

- 1 

Instruction 

Manual    - 

Fuse 0.5

А

 

 

 

 

 

- 1 pc 

Screw-nail 

    - 

pcs 

Dowel 

     - 

pcs 

Plastic 

Bushing 

    - 

pcs 

Front Cover Lock Key 

 

 

 

- 2 pcs 

Package 

    - 

pc 

ISO 9001 

Reviews: