T
r
oubleshooting
ONYX MOSFET Amplifier User’s Manual - page 18
ONYX MOSFET Amplifier User’s Manual - page 19
ONYX MOSFET Amplifier User’s Manual - page 5
ONYX MOSFET Amplifier User’s Manual - page 9
ONYX MOSFET Amplifier User’s Manual - page 15
ONYX MOSFET Amplifier User’s Manual - page 17
ONYX MOSFET Amplifier User’s Manual - page 4
General precautions
ONYX MOSFET Amplifier User’s Manual - page 3
Features
About 2 Ohm operation
ONYX MOSFET Amplifier User’s Manual - page 6
ONYX MOSFET Amplifier User’s Manual - page 13
ONYX MOSFET Amplifier User’s Manual - page 14
ONYX MOSFET Amplifier User’s Manual - page 16
ONYX MOSFET Amplifier User’s Manual - page 12
ONYX MOSFET Amplifier User’s Manual - page 8
ONYX MOSFET Amplifier User’s Manual - page 11
ONYX MOSFET Amplifier User’s Manual - page 10
ONYX MOSFET Amplifier User’s Manual - page 7
Specifications
Notes
If you experience operation or performance pr
oblems with this pr
oduct, compar
e your
installation with the electrical wiring diagram on the pr
evious pages. If pr
oblems persist,
read the following tr
oubleshooting tips which may help eliminate the pr
oblems.
Pr
otection LED
comes on when
amplifier is
power
ed up.
Check for short circuits on speaker leads.
T
ur
n down the volume control on the head unit to pr
event overdriving.
Remove speaker leads, and r
eset the amplifier
. If the Protection LED
still
comes on, then the amplifier is faulty and needs ser
vicing.
High hiss in the
speakers.
Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then
plug in the component driving the amplifier and unplug its inputs. If the
hiss disappears at this point, go on until the faulty/noisy component is
found.
It is best to set the amplifier's input level control as low as possible. The
best subjective signal-to-noise ratio is achieved in this manner
. T
ry to set
the head unit as high as possible (without distortion) and the amp input
level as low as possible.
Squealing noise
fr
om speakers.
Check for improperly grounded RCA interconnects.
Distorted sound.
Check that the Input Level Control is set to match the signal level of the
head unit. Always tr
y to set the Input Level as low as possible.
Check that all crossover fr
equencies ar
e properly set.
Check for short circuits on the speaker leads.
Amplifier gets
very hot.
Check that the minimum speaker impedance for the amp model is corr
ect.
Check that ther
e is good air circulation around the amp. In some
applications, it may be necessar
y to add exter
nal cooling fan(s).
Engine noise
(static type)
This is usually caused by poor quality RCA cables,which can pick up
radiated noise. Use only the best quality cables, and route them away
from power cables.
Engine noise
(alternator
whine)
Check that speaker leads ar
e not shorted to the vehicle chassis.
Check that the RCA grounds ar
e not shorted to the vehicle chassis.
Check that the head unit is properly grounded.
T
ri-Mode
Before installing and using your
new
amplifier, please be-
come familiar with all the infor-
mation contained in this manual.
Please keep this manual in a safe
place for future reference.
• Do not open or attempt to repair
this unit yourself. Dangerous high
voltages are present which may result
in electric shock. Refer any repairs to
a qualified service technician.
• To avoid risk of electronic shock or
damage to the amplifier, do not permit
any of this equipment to become
damp or wet from water or drinks. If
this does occur, immediately unplug
the power wires and send the amplifier
to your local dealer or service center
as soon as possible.
• If there is smoke or any peculiar
odor present during use or if there is
damage to any of the component
enclosures, immediately unplug the
power wire and send the amplifier to
your local dealer or service center as
soon as possible .
7. Insert fuse(s) into the battery fuse
holder(s).
8. Recheck all connections before
powering up the amplifier.
9. Set all level controls to minimum
position, and set all crossover
controls/switches to the desired
frequency points.
10. Power up the head unit and the
amplifier. Then set the volume control
on the head unit to about 3/4 volume,
and adjust the amplifier’s input level
control(s) to just below the level of
distortion.
11. Further fine tuning of the various
controls may be necessary to obtain best
results.
Your ONYX amplifier has been
designed to operate efficiently at loads
down to 2 Ohms. This means that you
can install four 8 Ohm speakers per
channel,
when using parallel wiring.
Increasing the number of woofers per
channel at low frequencies (below
100Hz) produces an acoustic coupling
effect. This acoustic coupling effect
increases your power output by about
3dB per speaker, or the equivalent of
an additional 10W per speaker.
When operating at 2 Ohms, the
amplifiers will increase their output
power by approximately 50%.
The
current draw will also increase by
about the same amount, so be sure
you have enough current to run the
amplifiers into a 2 Ohm load.
If you lack adequate current, your
music reproduction will be distorted.
Low-level (RCA) input wiring is preferred for best audio performance. Always use
a high-quality RCA cable for best audio performance.
T
ri-Mode
To Audio
Outputs of head
unit or signal
processor
High Level Input Wiring
Low Level Input Wiring
To Audio Outputs
of head unit or
signal processor
NX3000.2
NX2000.2
NX1600.2
Two Channel
MOSFET Car Audio
Amplifiers
NX3000.4
NX2500.4
NX2000.4
Four Channel
MOSFET Car Audio
Amplifiers
Congratulations on your
purchase of a
ONYX
Amplifier.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
your choice for car audio
entertainment!
NX2800.1
NX1800.1
MonoBlock
MOSFET Car Audio
Amplifier
All specifications subject to change without notice.
RMS POWER
into 4 Ohms
MAX POWER
into 2 Ohms
BRIDGED POWER
into 4 Ohms
Min. speaker
impedance
THD
Fr
equency r
esponse
Signal-to-noise ratio
Channel separation
Damping factor
Cr
ossover range
low pass
high pass
Bass boost
Fuse rating
Dimensions:
(10" x 2
-3/16
" x ...)
MODEL
4-Channel MOSFET Amplifiers
RMS POWER
into 4 Ohms
MAX POWER
into 2 Ohms
BRIDGED POWER
into 4 Ohms
Min. speaker
impedance
THD
Fr
equency r
esponse
Signal-to-noise ratio
Channel separation
Damping factor
Cr
ossover range
low pass
high pass
Bass boost
Fuse rating
Dimensions:
(10" x 2
-3/16
" x ...)
MODEL
2-Channel MOSFET Amplifiers
1500W x 1
2800W X 1
n/a
2 Ohm Ster
eo
4 Ohm Mono Bridged
0.01%
15-250Hz
100dB
90dB
125+
35Hz-160Hz
n/a
V
ariable 0 - +18dB
25A x 2
15-1/8"
SYMPTOM
POSSIBLE REMEDY
Connect the Positive (+) terminal of the
subwoofer to the L (+) amplifier terminal.
Connect the Negative (-) terminal of the
subwoofer to the R (-) amplifier terminal.
Two
Channel
Mode
Bridged
Mode
Four Channel Mode
Bridged Mode
Connect the Postive (+) ter
minal of the RIGHT
subwoofer to the CH3(+) amplifier ter
minal.
Connect the Negative (-) ter
minal of the RIGHT
subwoofer to the CH4(-) amplifier ter
minal.
Connect the Postive (+) ter
minal of the LEFT
subwoofer to the CH1(+) amplifier ter
minal.
Connect the Negative (-) ter
minal of the LEFT
subwoofer to the CH2(-) amplifier ter
minal.
Chassis
ground
point
To FRONT
Audio Outputs
of head unit or
signal processor
To REAR
Audio Outputs
of head unit or
signal processor
To Speaker Terminals
of head unit
To Speaker Terminals
of head unit
