background image

Important! Read First  ......................................

Fastener Legend...............................................

Front and Back Plates.......................................

Rear Shaft Assembly.........................................

Front Shaft to Keel............................................

Front Height Shaft to Spine...............................

Saw Spine to Keel.............................................

Rear Height Screw to Keel................................

Pitch Adjustor Assembly....................................

Rear Spine Guide.............................................

Pitch Adjustor/ Spine Guide..............................

Front Spine Guide............................................

Saw Blade Guides............................................

Transmission Check.........................................

Travelers...........................................................

Keel Assembly to Frame...................................

Assembly Detail................................................

Dovetail Ways...................................................

Inside Dovetail Sliders......................................

Table Bumpers..................................................

Outside Dovetail Sliders....................................

Fence and Trap Clamps....................................

Saw Blade.........................................................

Blade Alignment................................................

Cursor and Flip Down Stops............................

Blade Height Stop.............................................

Optional Stand..................................................

Stand Corner Key.............................................

Lubrication Guide.............................................

Cutting guide....................................................

Notes ...............................................................

Parts List..........................................................

1

4

5

5

6

6

7

7

8

8

9

9

10

10

11

11

12

12

13

13

14

14

15

15

16

16

17

18

19

20

21

22

USER’S GUIDE

Made in the USA

www.BridgeCityTools.com

1101-284-08 Rev. 1

Summary of Contents for Jointmaker Pro Signature Series

























Reviews: