background image

Instruction Book Part number: 2108521

We reserve the right to alter this product without notice in our constant endeavour for improvement.

     2005 Britax Childcare Pty. Ltd. This product is covered by Australian and overseas patent applications.
Patents Pending.

Series Number: 7000/B/5/2000 and 7000/B/5/2004

The 

Safe-n-Sound

 trade mark is the property of Britax Childcare Pty. Limited-Australia. 

The 

Britax

 trade mark is the property of Britax Excelsior Limited-UK.

Visit the Britax Web Site at http://www.britax.com.au or Email us at: custserv@britax.com.au

C h i l d  r e s t r a i n t  f o r  v e h i c l e  u s e .

Install with lap or lap-sash seat belt and upper

anchorage strap for children 

8kg to 18kg.

 

F o r w a r d  F a c i n g .

I n s t r u c t i o n s  f o r I n s t a l l a t i o n  &  U s e

Forward Facing

Child Restraint

Series number: 7000/B/5/2000 and 

  

7000/B/5/2004

INFORMATION FOR BUYERS:

FOR CHILDREN FROM 8KG TO 18KG.

CHECK THAT THIS CHILD RESTRAINT WILL FIT IN YOUR CAR.

IMPORTANT: 

KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT.

Child 

Restraint

CH

ILD 

RE

ST

RA

IN

T

Summary of Contents for FORWARD FACING CHILD RESTRAINT











Reviews: