How is hydrogen stored?
Hydrogen is stored in small cartridges (HYDROCORE) at low pressure. When refueling, hydrogen gas is sent into
the cartridge at high pressure, and adsorbed onto the surface area of a special metal alloy which is contained
inside the cartridges, thus becoming a solid (hydride). When connected to the fuel cell, the HYDROCORE
cartridges slowly release hydrogen using a heat exchange process with the ambient temperature.
How can I refill HYDROSTIK cartri
dges with hydrogen?
Add water into the unit’s water tank, connect the AC-DC adapter and insert a HYDROCORE cartridge. The
HYDROLYSERwill split water into hydrogen and oxygen, sending hydrogen into the HYDROCORE cartridge. It will
take around
What is the purity level of the hydrogen produced by the HYDROLYSER
?
The purity of the hydrogen produced by the HYDROLYSER is 99%
. The metal hydrides contained in the cartridge
first adsorb hydrogen, then release it at a higher purity into the fuel cell.
When do I need to add water to the water tank?
When should I empty the drainage tank?
When the waste tank is full, pour waste water out and refill the water tank.
FREQUENTLY ASKED QUESTIONS
The LED light alternates between red for 1 second and off for 3 seconds.
SOLUTION
: Try to add 40°C to 70°C water into the water tank.
The LED light alternates between red for 1 second and off for 1 second.
SOLUTION
: Check the water level of the water tank and waste water tank is correct. Either add
water to the water tank or remove water from the waste water tank as required.
Q:
3.
4
.
5
.
4
6.
T
SOLUTION A
:
y.
SOLUTION B
: Check the water temperature (see 4. SOLUTION A)
SOLUTION A
SOLUTION B
: Disconnect the cartridge and connect it to a fuel cell product to confirm
there is hydrogen in the cartridge.
Q:
A:
Q:
A:
Q:
A:
2
.
SOLUTION A:
smooth
and the HYDROCORE is fully inserted into the thread.
SOLUTION B:
SOLUTION C:
Remove and re-connect the AC-DC adapter.
USER MANUAL
SPECIFICATIONS
•
Do not tamper with, or disassemble the HYDROFILL
• Keep HYDROLYSER away from fire, open flame, or heat sources
• Keep HYDROCORE cartridge away from fire, open flame, or heat so
urces
• Keep HYDROLYSER away from children
• Add
carefully to avoid over-filling the water tank
W
ARNING
1
HYDROLYSER
Water tank cover
Status indicator
HYDROCORE
cartridge port
(
a)
HYDROLYSER unit
Waste water tank
Water tank
Stack type
Water input
Proton exchange membrane electrolysis cell
De-ionized or dis lled water
D
i
m
ensions
(W x D x H)
145 x 153 x 208 mm (5.7 x 6 x 8.2 in)
Input voltage
DC: 10V-19V
Water
Approx. 20ml/hr (1.2in /hr)
Weight
1.8Kg ±5% (3.97Lbs ±5%)
99% (designed for HYDROCORE only )
P
urity
O
ut
l
et speci
fi
ca on
Designed for HYDROSTIK only
Hydrogen genera on capacity
Up to 3L/hr (0-183 in /hr)
Hydrogen output pressure
0-3.3 MPaG (0-478.62 PSI)
3
Wate
r temperature
10-40°C (50-104°F)
3
Rated power
≤23W
R
e
fill
ing
m
e
f
or
one HYDROCORE
Around 4 hours (at 25C ambient temperature)
SYSTEM OVERVIEW
The HYDROLYSER system uses a proton exchange membrane
(PEM) electrolyzer to recharge Horizon’s HYDROCORE metal
Quiet, safe and convenient hydrogen supply
products such as HYDROGEN REACTOR
High hydrogen purity 99%
Connects to AC power
SYSTEM FEATURES
(
b)
AC-DC adapter
(
c)
User Manual
INCLUDED IN THIS BOX
a.
HYDROLYSER unit
b. AC-DC adapter cord
c. User Manual
HYDROLYSER
User Manual
*
One way to check the volume of hydrogen inside a cartridge, is to weigh the HYDROCORE
empty HYDROCORE is around 0.9 grams.
A:
Q:
A:
Q:
A:
HYDROLYSER
HYDROLYSER
HYDROCORE
HYDROLYSER
HYDROLYSER
HYDROCORE
technical@bruntongroup.com
HYDROCORE
BRAND MARK
HYDROCORE
HYDROCORE
BRUNTON
