background image

1

912SC 92.1 AFUE

LEGACY

t

LINE SINGLE--STAGE

4--WAY MULTIPOISE

CONDENSING GAS FURNACE, SERIES A

Product Data

A11264

The 912S Multipoise Condensing Gas Furnace is part of the

Legacy

t

Line product offering. Sporting a PSC blower motor

and an Annual Fuel Utilization Efficiency (AFUE) of 92.1%, this

single-stage gas furnace provides efficient comfort for
homeowners. This Legacy Line Gas Furnace also features 4-way

multipoise installation flexibility, and is available in eight model

sizes. The 912S can be vented for direct vent/two-pipe, ventilated
combustion air, or single-pipe applications. A Bryant

R

Air

Conditioner or Heat Pump can be used to form a complete system.
All units meet California Air Quality Management District

emission requirements. These furnaces are approved for

Manufactured Housing (Mobile Home) applications. All sizes are
design certified in Canada.

STANDARD FEATURES

S

4-way multipoise design for upflow, downflow or horizontal
installation.

S

Optional through-the-cabinet downflow venting.

S

Installation flexibility with a 360-degree rotating elbow.

S

Ideal condensing furnace height 35” cabinet: short enough for
taller coils, but still allows enough room for service.

S

Silicon Nitride Perfect Light

t

Hot Surface Igniter.

S

Aluminized-steel primary heat exchanger.

S

Stainless-steel condensing secondary heat exchanger.

S

High-quality corrosion-resistant prepainted steel cabinet with
hemmed edges for safety.

S

Factory-configured ready for upflow applications.

S

Direct-vent/sealed combustion, single-pipe venting or ventilated
combustion air.

S

PSC blower motor, single-speed inducer motor, and single-stage
gas valve.

S

Self-diagnostics

S

Approved for Twinning applications (36060 through 60120
sizes, only).

S

Propane convertible (See accessory list).

S

Approved for Manufactured Housing/Mobile Home applications
with MH accessory kit.

S

Convenient Air Purifier and Humidifier electrical connections.

S

Residential installations may be eligible for consumer financing
through the Retail Credit Program.

S

Certified to leak 2% or less of nominal air conditioning CFM
delivered when pressurized to 1-inch water column with all
present air inlets, air outlets, and condensate drain port(s) are
sealed.

Use of the AHRI Certified 

TM

 Mark indicates a

manufacturer’s participation in the program.  For
verification of certification for individual products,
go to www.ahridirectory.org.

C E RT I F I E D

Summary of Contents for 912SC

















Reviews: