background image

Installation  Instructions

124ANS

PREFERRED

t

 SERIES AIR CONDITIONER

WITH PURON

r

 REFRIGERANT

1

1/2 TO 5 NOMINAL TONS

Fig. 1

 - 

124ANS

NOTE

:  Read the entire instruction manual before starting the

installation.

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS

1

. . . . . . . . . . . . . . . . . . . . . . . .

INSTALLATION

2

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Complete Pre

Installation Checks

2

. . . . . . . . . . . . . . . . . . .

Rig and Mount Unit

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Complete Refrigerant Piping Connections

3

. . . . . . . . . . . . .

Make Electrical Connections

3

. . . . . . . . . . . . . . . . . . . . . . . .

START

UP

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SERVICE

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, maintenance,

or use can cause explosion, fire, electrical shock, or other

conditions which may cause death, personal injury, or property

damage. Consult a qualified installer, service agency, or your

distributor or branch for information or assistance. The qualified

installer or agency must use factory

authorized kits or accessories

when modifying this product. Refer to the individual instructions

packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Use quenching cloth for brazing operations.

Have a fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in

literature and attached to the unit. Consult local building codes and

the current editions of the National Electrical Code (NEC)

NFPA70.
In Canada, refer to the current editions of the Canadian Electrical

Code CSA C22.1.
Recognize safety information. This is the safety

alert symbol 

.

When you see this symbol on the unit and in instructions or

manuals, be alert to the potential for personal injury. Understand

the signal words 

DANGER

WARNING

, and 

CAUTION. 

These

words are used with the safety

alert symbol. 

DANGER 

identifies

the most serious hazards which 

will 

result in severe personal injury

or death. 

WARNING 

signifies hazards which 

could 

result in

personal injury or death. 

CAUTION 

is used to identify unsafe

practices which 

may 

result in minor personal injury or product and

property damage. 

NOTE 

is used to highlight suggestions which

will

 result in enhanced installation, reliability, or operation.

!

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury

or death.
Before installing, modifying, or servicing system, main

electrical disconnect switch must be in the OFF position.

There may be more than 1 disconnect switch. Lock out and

tag switch with a suitable warning label.

ENVIRONMENTAL HAZARD

Failure to follow this caution may result in environmental

pollution.
Remove and recycle all components or materials (i.e. oil,

refrigerant, etc.) before unit final disposal.

CAUTION

!

Summary of Contents for PREFERRED 124ANS







Reviews: