background image

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601    FAX: (217) 529-6644

www.bunnomatic.com

OPERATING & SERVICE MANUAL

CEZ
CDBC
TWIN

CAUTION :

CAUTION :

CAUTION :

CAUTION

DISCARD DECANTER
IF:

. C

RACKED

. SCRATCHED

. BOILED DRY 

. H

EATED WHEN EMPTY

. USED O

N HIGH FL

AME

. O

R EXPOSED ELECTRIC

  ELEMENTS

FAILURE TO COMPLY RISKS INJURY

PN: 658

1985

 BUNN-O

-MATIC CORP

OR

AT

ION

FUNNEL CONTENTS
        ARE HOT

!

CAUTION

DISCARD DECANTER
IF:

. CRACKED

. SCRATCHED

. BOILED DRY 

. HEATED WHEN EMPTY

. USED ON HIGH FLAME

. OR EXPOSED ELECTRIC

  ELEMENTS

FAILURE TO COMPLY RISKS INJURY

PN: 658

1985 BUNN-O-MATIC CORPORATION

FUNNEL CONTENTS
        ARE HOT

!

CAUTION

DISCARD DECANTER
IF:

. CRACKED

. SCRATCHED

. BOILED DRY 

. HEATED WHEN EMPTY

. USED ON HIGH FLAME

. OR EXPOSED ELECTRIC

  ELEMENTS

FAILURE TO COMPLY RISKS INJURY

PN: 658

1985 BUNN-O-MATIC

 CORPORATION

FUNNEL CONTENTS
        ARE HOT

!

ON/LOWER

START

TOP

ON/LOWER

START

TOP

29319.0000D    09/03   ©1999  Bunn-O-Matic Corporation

Summary of Contents for CDBC





































Reviews: