Thank you for purchasing Keyguard
by Burton Safes Ltd. In order to
correctly install and use your
Keyguard it is important that you
read and follow these instructions
carefully.
www.burtonsafes.co.uk
01484 663388
GETTING STARTED.
Please note that all Keyguard safes are
supplied without a preset code. To open
the Keyguard for the first time replicate
the following steps:
1.
With the Keyguard in an upright position
(As pictured) slide the button marked ‘Clear’
downwards and then release it allowing the
button to return to its usual position.
2.
Firmly hold the facia of the Keyguard
and simultaneously slide the button marked
‘Open’ downwards. With the ‘Open’ button
still pushed downward pull the facia away
from the safe body.
SETTING YOUR OWN CODE.
1. Place the facia of the Keyguard face
down on a firm surface.
2. Decide upon your new personal code,
please be aware that you may only use
each number and / or letter once. (It is
suggested that you select a 4-8 digit
figure for your new code. It is very
important that you remember this
combination.)
3. To set your code you will require a
small flat-headed screwdriver. Observe
that on the back of the Keyguard facia
there are twelve slotted disks with arrows
pointing upward. These disks are
numbered or lettered and represent each
of the twelve available digits. Flip the
safe cover face up and familiarise
yourself with which disks represent which
number.
4. Unscrew the small screw that holds
the numbered plastic plate in position.
Now remove the plate from the facia.
5. Using the screwdriver turn the disk
that represents the first number or letter
in your code 180
°
so that the arrow now
points downward. Repeat this step for
each number and / or letter in your code.
6. Replace the numbered plastic plate
and secure it in position with the small
screw.
7. Once you have input your code you
should check that it has been correctly
set. It is vital that you first check this with
the Keyguard open
. DO NOT YET
REPLACE THE FACIA!
CHECKING YOUR CODE.
1. With the Keyguard facia in an upright
position slide the button marked ‘Clear’
downwards and then release it allowing the
button to return to its usual position.
2. Input each digit of your personal code,
one figure at a time. It does not matter
which order you punch in your numbers
and / or letters. For instance if your
personal code is 1-2-3-4-B you can input
your code as B-4-3-2-1 or 3-1-B-2-4 etc.
and the Keyguard will still operate.
3. Once you have depressed the buttons
for each number in your code the ‘Open’
button should slide easily downwards.
N.B. If any of the numbered buttons fail to
depress after you have set your code
then please ensure that they have been
turned fully 180
°
.
4. Re-check that your code works two or
three more times. If these tests are
successful you can now place the
Keyguard facia into its position on the
body.
REPLACING THE FACIA.
1. Start by resetting the lock by sliding
down the clear button and releasing it.
2. Input your new personal code and
depress the ‘Open’ button (Do not
release the open button yet.).
3.
Note that on the lowest edge of the
facia there is an extended metal keep.
Locate this keep into the shaped recess
on the lowest inside surface of the
Keyguard body.
4.
Push the facia forward into position
and release the ‘Open’ button. The
Keyguard should now be shut.
NORMAL KEYGUARD USE.
Your Keyguard can now be operated
using the techniques you have learnt
so far. The following points should
help clarify any final uncertainties.
1. During any operation of the
Keyguard always begin by depressing
the ‘Clear’ button.
2. To open first input your personal
code and depress the ‘Open’ button,
whilst simultaneously pulling the facia
towards you.
3. To close the Keyguard follow the
steps described in the section
‘Replacing the facia’.
CHANGING YOUR CODE.
You may wish at some stage to alter the
personal code you have set. You can
change your code by following the steps
below.
1. In the usual manner open your
Keyguard and remove the facia.
2. To change the code you will need a
small flat-headed screwdriver. Now
begin by placing the facia face down.
3. Unscrew the small knob that holds the
numbered metal plate in position. Now
remove the plate from the facia.
Keyguard Instructions
