background image

MEZZANINE GATE SYSTEM  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTALLATION  

 

AND OPERATION

 

INSTRUCTIONS

 

 

 

 

 

 

 

Keep this Manual with the MEZZANINE 
GATE system at all times. This will allow 
new users to read it before using system. 

 
 

It  is  the  MEZZANINE  GATE 

owner’s  responsibility  to  ensure  that  all 

workers installing or using this system are thoroughly trained. Provide 
workers with  this  Installation  Manual  and  make  sure  they  understand 
its  contents.  Read  it  to  them  if  necessary.  Letting  poorly  trained 
workers use this system can result in property damage and/or serious 
injury or death to personnel. 

 

WARNING! 

MEZZANINE GATE System must be installed according to the 
instructions outlined in this manual. Failure to do so could result in 
serious injury or death to personnel! 
 
To prevent serious injury or death, MEZZANINE GATE System must be 
installed using hardware provided by Garlock Equipment Company! 
 
To prevent serious injury or death, Installers of System must use 
OSHA-approved Tie-Off device to install or remove this System. 

 

 

 

 

            

 

Distributed by

CAI Safety Systems

Summary of Contents for MEZZANINE GATE













Reviews: