INSTALLATION INSTRUCTION FOR
CAL-ROYAL
N-FMR7700 SERIES MORTISE EXIT DEVICE
BEFORE INSTALLING DEVICE, PLEASE CHECK:
1. IF DOOR FITTED AND HUNG.
2. SIZE OF EXIT DEVICE, FUNCTION AND DESIGN ...
2.1. 36"DOORS, CAN BE CUT TO FIT DOORS DOWN TO 30" WIDE.
2.2. 48"DOORS, CAN BE CUT TO FIT DOORS DOWN TO 36" WIDE.
2.3. HAND OF DEVICE AGAINST APPLICATION.
OUT
RIGHT HAND
��
REVERSE BEVEL �
•
�
LEFT HAND
REVERSE BEVEL
CHASSIS
ASSEMBLY
HORIZONTAL
�CHASSIS
1. PREPARE DOOR AND MOUNT LOCK
Tape templates to inside face and edge of doors according to
directions given on template. Drill holes and mortise door for
lock as indicated.
vERTIcAL
'i,_
OF cHAssIs
Fasten mortise lock in plate
NOTE:lf screwless rose trim
is used -- refer to trim
instructions and mount
2-3/4"
TO FINISHED FLOOR
FROM TEMPLATE
SURFACE OF DOOR FOR
EXIT DEVICE APPLIED MUST
BE FLUSHED.
END CAP
RAIL MOUNTING
BRACKET
3. APPLY EXTERIOR TRIMS
If ESC lever trim is used, attach outside trim and cylinder.
4. APPLY RAIL ASSEMBLY
1. CHECK THE SIZE OF DEVICE, IF CUTTING TO LENGTH IS REQUIRED.
2. DETERTMINE CUT OFF LENGTH "X" BY SUBTRACTING 1-3/4" (44.5mm)
FROM "Y". MARK CUT OFF POINT ON MOUNTING RAIL.
VERTICAL
CHASSIS
FOR DOOR W/STILE
CUT OFF MUST LEAVE
1/2" MIN OVERLAP
WITH RAIL
I
f
�:
i •
=======-=·
::r-------:,
(
! �
X
-l
1-3/4" MIN
1------��------i·
(44.5 mm)
t-------Y�------i
CUT OFF AND DEBURR
DON'T CUT CLOSER THAN
1-3/4" (44.5mm) FROM LOWER PIUOT.
lock in conjunction with
rose and inner plates
OR FROM RELATIONSHIP
TO STRIKE
3. DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO
CHASSIS. LEVEL RAIL AND FASSTEN CHASIS AND MOUNTING
PLATE.
#12-24x1"
<t_ LATCH BOLT
2. ATTACH CHASSIS TO DOOR
2.1 Attach chassis to Rail, then lock
push rail down.using
2.2 Position chassis and rail on door,
so that lever arm is under rear
section of Mortise lock lever.
Then lift up until latchbolt is
completely retracted.
2.3 With chassis in this position and
rail horizontal, mark location of
chassis mounting holes. Drill holes
for screws.
2.4 Release Push rail, and dis-ass'y
chassis from rail.
Then, mount chasis on door.
LATCH BOLT
INSIDE FACE
OF DOOR
DEPRESS ARM INTO RAIL OPENING AND
SLIDE RAIL ONTO CHASSIS
PUSH RAIL
RAIL ASSEMBLY
r--------
CHASSIS
i
LEVEL
\ RAIL ASSEMBLY.
lj
MOUNTING PLATE SCREWS
5. APPLY COVER AND STRIKES
ATTACH COVER TO CHASSIS
WITH (4) #8 TRUSS HEAD
MACHINE SCREW.
ATTACH END CAP TO
MOUNTING PLATE WITH
(2) COVER SCREWS.
D D
LEFT
RIGHT
ATTACH STRIKE TO
DOOR STOP WITH (2), STRIKE
SCREW AND LOCK WASHER
ATTACH MOUNTING PLATE TO
DOOR WITH
(2)
ROUND HEAD
SCREWS.
LEFT
RIGHT
ATTACH STRIKE TO
DOOR STOP WITH (2), STRIKE
SCREW AND LOCK WASHER
DRWG. # EDG4026
1-2
