background image

  Operating Instructions  

AT2000, TL0535

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. 
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or 
property damage! Retain instructions for future reference.

Description

Professional air powered cut-off tools 
are air tools designed for a variety of 
cutting applications, and can be used 
on many metals. Used for cutting 
rusted exhaust bolts, auto panels and 
various home projects.

Unpacking

When unpacking this product, carefully 
inspect for any damage that may have 
occurred during transit. 

Safety Guidelines

This manual contains information that is 
very important to know and understand. 
This information is provided for SAFETY 
and to PREVENT EQUIPMENT PROBLEMS. 
To help recognize this information, 
observe the following symbols. 

 

Danger indicates an 

 imminently 

hazardous situation which, if not 
avoided, WILL result in death or serious 
injury.

 

Warning indicates a 

 

potentially 

hazardous situation which, if not 
avoided, COULD result in death or 
serious injury.

 

Caution indicates a 

  

potentially 

hazardous situation which, if not 
avoided, MAY result in minor or 
moderate injury.

General Safety 

Information

CALIFORNIA PROPOSITION 65

 

This product can 

 

expose you to 

chemicals including lead, which are 
known to the State of California to 
cause cancer and birth defects or other 
reproductive harm. For more 
information go to www.P65Warnings.
ca.gov.

You can create dust when you 
cut, sand, drill or grind materials 
such as wood, paint, metal, concrete, 
cement, or other masonry. This dust often 
contains chemicals known to cause cancer, 
birth defects, or other reproductive harm. 
Wear protective gear.

ILLINOIS LEAD POISONING 
PREVENTION ACT

 CONTAINS 

LEAD. 

 

MAY BE HARMFUL 

IF EATEN OR CHEWED. COMPLIES WITH 
FEDERAL STANDARDS.

This product is part of a high pressure 
system and the following safety 
precautions must be followed at all 
times along with any other existing 
safety rules.
1.   Read all manuals included 

with this product care-fully. 
Be thoroughly familiar 
with the controls and the 
proper use of the equipment.

2.   Only persons well acquainted with 

these rules of safe operation should 
be allowed to use the air tool.

 

 Do not exceed the 

  maximum oper-ating 

pressure of the air tool (90 psi). This can 
reduce the life of the tool.

3.   Do not exceed any pressure rating 

of any component in the system. 
Maximum operating pressure of 90 
psi is measured at the tool inlet 
while the tool is running. The 
pressure drop between the 
compressor and tool needs to be 
compensated for at the compressor.

4.   Disconnect the air tool from air 

supply before changing tools or 
attachments, servicing and during 
non-operation.

 

Safety 

 glasses and 

ear protection must be worn 
during operation.

 IN248104  1/19

5.  Do not wear loose fitting clothing, 

scarves, neck ties or jewelry when 
operating any tool. Loose clothing 
or jewelry may become caught in 
moving parts and result in serious 
personal injury.  

6.   Do not depress trigger when 

connecting the air supply hose.

7.   Always use attachments designed 

for use with air powered tools. Do 
not use damaged or worn 
attachments.

8.   Never trigger the tool when not 

applied to a work object. Attach-
ments must be securely attached. 
Loose attachments can cause serious 
injury.

9.   Protect air lines from damage or 

puncture.

10. Never point an air tool at oneself or 

any other person. Serious injury 
could occur.

11. Check air hoses for weak or worn 

condition before each use. Make 
sure all connections are secure.

 

Release all 

 pressure 

from the system before 
attempting to install, service, 
relocate or perform any 
maintenance.

12. Keep all nuts, bolts and screws tight 

and ensure equipment is in safe 
working condition.

13. Do not put hands near or 

under moving parts. Keep 
hands off guard when 
operating. Do not operate 
tool without guard 
properly secured.

14. Always secure workpiece in a vise or 

clamp.

 

 Do not misuse this 

 product. Excessive 

exposure to vibration, work in awkward 
positions and repetitive work motions can 
cause injury to hands and arms. Stop using 
any tool if discomfort, numbness, tingling 
or pain occur, and consult a physician. 

MANUAL

Air Cut-Off Tool

For parts, product & service information

visit 

www.campbellhausfeld.com

© 2019 Campbell Hausfeld
A Marmon/Berkshire Hathaway Company

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

See Warranty on page 4 for important information about commercial use of this product.

Summary of Contents for AT2000













Reviews: