background image

WARRANTY 

 

CANARM Ltd. warrants every new product to be free of defects in material and workmanship, to the extent that, within a period of one year 

from the date of purchase CANARM Ltd. shall either repair or replace at CANARM’s option, any unit or part thereof, returned freight prepaid, and 

found to be defective. 

 

This warranty does not include any labour or transportation costs incidental to the removal and reinstallation of the unit at the user’s premises. 

Components repaired or replaced are warranted through the remainder of the original warranty period only. 

 

This warranty applies to the original purchaser-user only; it is null and void in case of alteration, accident, abuse, neglect, and operation not in 

accordance with instructions.

INSTALLATION OR PRODUCT PRObLEMS?  DO NOT RETURN TO STORE Of PURChASE. 

CONTACT CANARM SERvICE AT 1-800-265-1833 (CANADA)  1-800-267-4427 (U.S.A.) 

1-800-567-2513 (EN fRANÇAIS)  MONDAy TO fRIDAy 8:00 - 5:00PM E.S.T.

GENERAL SAFETY

Rotating parts, (pulleys, shafts and belts) on fans should not be exposed. Where these components are not protected by ductwork, cabinets 
or covers, appropriate guards should be employed to restrict exposure to rotating parts. Access doors should not be opened with the fan 
operating to avoid foreign objects being drawn into the system. On initial start-up, a careful inspection should be carried out to ensure no 
foreign material is present which could become airborne in the system. 
 
Read installation and operation instructions carefully before attempting to install, operate or service Canarm/Delhi 600 Series. Failure to 
comply with instructions could result in personal injury and/or property damage. 

Retain instructions for future reference.

600 SERIES_04_08_22

Page 1 o

f

 4

600 SERIES 

UTILITY BLOWERS

OPERATION INSTRUCTIONS AND PARTS MANUAL 

READ AND SAVE THESE INSTRUCTIONS 

600 SERIES MODELS: 610, 612, 615, 618, 620, 622, 625

NOTICE: 

No warranty claims will be honored by CANARM Ltd. unless prior authorization is obtained.

Summary of Contents for 600 Series









Reviews: