Easy Start Guide
Document Scanner DR-2050C/SP
☞
Continued on back side
PUB. CE-IE-546
©2007 CANON ELECTRONICS INC.
Thank you for purchasing the Canon DR-2050C/DR-2050SP Document Scanner. This Easy
Start Guide describes the procedure for setting up the scanner for use. Follow the
procedures outlined in this Easy Start Guide to set up the scanner. Details on using the
scanner are described in the User’s Guides packaged with the scanner. Before you use the
scanner, make sure to thoroughly read the User’s Guides.
Checking the Accessories
When you unpack your scanner, make sure that it contains all of the following accessories. If
any of the items listed below are missing or damaged, contact your local authorized Canon
dealer or service representative.
Removing the Packing Materials and
Installing the Feed Roller
Remove the scanner from the box, remove the orange tape and protective sheets from the
scanner, and install the feed roller on the scanner body.
1.
Peel off the four pieces of orange tape from the outer casing.
2.
Open the document feed tray and remove the protective sheet.
C A N O N C A N A D A I N C .
6 3 9 0 D I X I E R D
M I S S I S S A U G A O N L 5 T 9 Z 9
0880281099-L5T1P7-BR01
Document
Guide Adapter
Remote Control
AAA Batteries (2)
Adobe Acrobat
Setup Disc
DR-2050C/DR-2050SP
User’s Guide
Easy Start Guide
(this document)
DR-2050C/DR-2050SP
Feed Roller
AC Adapter/Power Cord
(Connected length: 8 ft. 6 in. (2.6 m))
USB Cable
Type A/Type B
(Length: 6 ft. (1.8 m))
DR-2050C
Setup Disc
Adjustment Sheet
*For the DR-2050SP, the following accessories are included in addition to the above items.
DR-2050SP User’s Guide
Presentation Mode Edition
RGB Cable
Mini D-sub 15 Pin
×
2
(Length: 5 ft. (1.5 m))
Warranty Card
(U.S.A. and Canada only)
Registration Card
(U.S.A. and Canada only)
3.
Open the front cover at (
1
1
1
1
1
) and (
2
2
2
2
2
), and remove the orange tape fastening the
roller cover.
4.
Open the roller cover.
5.
Lower the roller lock lever (
1
1
1
1
1
), and slide it towards the left (
2
2
2
2
2
).
6.
Load the feed roller, align the notch on the roller with the shaft on the scanner
body.
7.
Slide the roller lock lever towards the right, fit the lever feed roller into the hole on
the left of the roller (
1
1
1
1
1
), and push down the roller lock lever to lock the feed roller
shaft (
2
2
2
2
2
).
8.
Close the roller cover. Make sure that the roller cover clicks into place.
9.
Gently push in the front unit on its left and right sides to close the front unit.
Make sure that the front unit clicks into place.
10.
Close the document feed tray and top cover.
Document Feed Tray
Top Cover
1.
Turn ON your computer.
2.
Insert the DR-2050C Setup Disc into the
PC’s CD-ROM drive.
The setup wizard automatically starts up
when you insert the CD-ROM into the CD-
ROM drive. If the setup wizard does not
start up, execute setup.exe in the CD-ROM.
3.
Click [Typical Installation].
If you click [Typical Installation], all of the
software is installed. If you want to select
which parts of the software to install, click
[Custom Installation].
4.
Click [Install].
All of the currently displayed software is
installed. To install only selected software,
click [Back] and select [Custom
Installation].
5.
Click [Next].
6.
Read the software license agreement, and
click [Yes] if you consent to the conditions of
the software.
Installation of the scanner driver starts.
During scanner driver installation, the
scanner driver and the Job Registration
Tool are installed.
7.
Click [Finish] to complete the installation.
Next, the installation wizard for
CapturePerfect 3.0 appears.
8.
Click [Next].
9.
Read the software license agreement, and
click [Yes] if you consent to the conditions of
the software.
10.
Check the destination folder and click [Next].
Installation of CapturePerfect 3.0 starts.
11.
Click [Finish] to complete the installation of
CapturePerfect 3.0.
12.
Next, installation of OmniPage SE starts.
Follow the messages on the screen to
proceed with the installation.
13.
When all installations are complete, the
Installation completed screen appears.
Click [Exit] to exit the installer.
(Click [Back] to return to the menu screen.)
14.
Remove the setup disc, and finish the
software installation.
Note
●
To use the feed roller, install it on the scanner.
☞
[STEP 2] “Removing the Packing Materials and Installing the Feed Roller”
●
Documents can be prevented from feeding slantwise by installing the document
guide adapters on the document guides. (
☞
STEP 5)
●
The adjustment sheet is used to adjust the scanner when anomalies begin to
appear in scanned images. Store it in a safe place where it will not be lost.
●
The DR-2050 Setup Disc contains the “DR-2050C Scanner Driver”,
“CapturePerfect 3.0”, and “OmniPage SE” made by Nuance Communications Inc.
☞
DR-2050C/DR-2050SP User’s Guide p.17 “About the Setup Disc”
●
Items included in this package are subject to change without notice.
●
You must keep the machine’s packaging and packing materials for storing or
transporting the machine.
After checking the package contents, you need to prepare the scanner
for use. (
☞
STEP 2)
The scanner is now ready for use.
Next, you need to install the scanner software. (
☞
STEP 3)
This completes the software installation.
Next, you need to connect the scanner to your computer. (
☞
STEP 4)
Note
●
When software is installed the icons are added to the Program menu.
(Windows 2000)
Installing the Software
Install the software before connecting the scanner to the computer.
❏
Before installing the software, make sure your computer is correctly running one of
the following versions of Windows. For details, refer to the DR-2050C/DR-2050SP
User’s Guide.
• Windows 98SE
• Windows Me
• Windows 2000 Professional SP4 or later
• Windows XP Home Edition SP2 or later
• Windows XP Professional SP2 or later
❏
Do not connect the scanner to the computer before installing the software. If you
connect the scanner and turn it ON before you install the software, a wizard screen
will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn
the scanner OFF.
Wizard Screen (Windows 2000)
❏
Be sure to log on with administrator privileges when logging on to Windows.
❏
Close all other applications before installing the software.
Warning
■
Trademarks
• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be
trademarks or registered trademarks in other countries.
• Microsoft Windows
®
is a registered trademark of Microsoft USA in the United States and other countries.
• Other brands and product names used in this manual may be trademarks or registered trademarks of their
respective companies.
