background image

E-IM-2514

Bluetooth Calculator Keypad / 

Bluetooth Teclado Calculadora

If the Calculator Keypad is not connected or not functioning properly:

 

Check battery placement direction.

 

Make sure computer meets the system requirements described.

 

Check if Bluetooth hardware and software are installed correctly and enabled.

 

Make sure the Bluetooth USB adapter (dongle) is functioning properly.

 

Remove obstacles between personal computer and the Calculator Keypad.

 

If recently connected (paired) with a different computer, reset the connection to 

your current computer by repeating the initial setup (re-pairing).

 

If unable to reset the connection to a previously paired computer, remove or delete 

the device before re-pairing (please follow your computer’s procedures on how to 

remove or delete a Bluetooth device).

 

If the display disappears after the Bluetooth is turned ON, press 

 key and 

check if the 

  icon appears.

 

Change to new batteries if the  

  icon appears.

 

If the “E” icon appears, the keypad is locked. Press 

 or 

  to clear and 

resume operation. (The “E” icon occurs when the result or memory content 

exceeds 10 digits to the left or when dividing by “0”.)

 

J

Electromagnetic interference or electrostatic discharge 

may cause any malfunction. Should this occur, use 

the tip of a ball point pen (or similar object) to press 

the [CAL RESET] button on the back of the Calculator 

Keypad. And turn off and on the Bluetooth Switch.

TROUBLESHOOTING

 

When using with a different computer, please pair again using the initial setup.

 

● The Bluetooth icon will remain on (solid, not flashing) when the Calculator Keypad 

is successfully connected to your computer.

 

To conserve battery, turn the Bluetooth connection off when travelling or when 

using as a calculator only without a computer.

 

Bluetooth connection requires battery power to function properly. 

 

When Bluetooth is off, calculator functions can be used without batteries  

(powered by solar panel).

USAGE TIPS

USER GUIDE / 

GUIA DE USARIO

PRINTED IN CHINA / IMPRESO EN CHINA

ENGLISH

IMPORTANT: READ BEFORE USE 

Please read the following instructions and safety 

precautions before using the Calculator Keypad.  

Keep this sheet on hand for future reference.

THIS DEVICE IS WINDOWS AND MACINTOSH COMPATIBLE

.

You will be prompted during setup to select an operating system (OS) using the 

Bluetooth OS switch on the back of the device. If the switch is set to an incorrect 

OS, the device may not function properly.
If your computer does not have a built-in Bluetooth device, you need to purchase 

a Bluetooth USB adaptor (dongle).
Before connecting the Calculator Keypad with your computer’s Bluetooth device 

or dongle, be sure the Bluetooth feature in your computer is enabled and ready.

WINDOWS VISTA

®

 AND WINDOWS

®

 7

Your computer is now setup to use your Calculator Keypad.

Click “

Close

” to finish.

5

1

Windows Vista

®

Go to “

Control Panel > Bluetooth Devices”

 

and 

click on “

Add Wireless Device

”.

Windows

®

 7

Go to “

Control Panel > Hardware and Sound > Devices and Printers” 

and click on “

Add a Device

”.

Press the “

PAIR

” button on 

the device using the tip of a  

pen or a similar object.

(NOTE: In the computer window, the “Canon X Mark I K”  

should appear in the list of new devices. If not, wait a moment  

and press the “PAIR” button again -or- move the Bluetooth switch to 

“OFF” and then to “PC ON”, and press the “PAIR” button again.)

3

2

To find the device, move 

 

the Bluetooth switch on the  

device to “

PC ON

”.

(NOTE: The   icon 

on the front display  

should be flashing.)

Select “

Canon X Mark I K

” and click “

Next

”.

(NOTE: Wait a moment while the computer connects to the device. 

It will take a few seconds for the computer to finish automatically 

installing the device. A notification should appear stating that the 

device has installed successfully.)

4

Hardware :

  Bluetooth-enabled (v2.0) computer (with either built-in Bluetooth or 

 

external Bluetooth dongle)

 

Windows based PC x86 / x64 or above, Intel-based Mac 

Operating  

Windows

®

 XP (SP2 or above) or Windows Vista

®

 or Windows

®

 7

System :

  Mac OS

®

 X 10.4 ~ 10.6 

SYSTEM REQUIREMENTS

 

Keep the batteries out of reach of children. 

 

Never expose batteries to high temperatures, direct heat, or dispose by incineration. 

 

Do not mix new and old batteries or batteries of different types. 

 

Do not allow metal objects to touch the battery terminals on the device; they can 

become hot and cause burns. 

 

Remove the batteries if they are worn out or have been stored for an extended 

period of time. 

 

Always remove old, weak, or worn out batteries promptly and recycle or dispose of 

them in accordance with Federal, State, and Local regulations. 

 

● If a battery leaks, remove all batteries, taking care to keep the leaked fluid from 

touching your skin or clothes. If fluid from the battery comes into contact with skin 

or clothes, flush skin with water immediately.

BATTERY CAUTION !

Model : 

X Mark I Keypad BT 

Power Source :

 AAA-size Alkaline batteries x 2

Wireless Connection :

 Bluetooth v2.0

Operating Temperature : 

0ºC to 40ºC (30ºF to 104ºF)

Dimension : 

155mm (L) x 86mm (A) x 20mm (A)

 

1-7/64” (L) x 3-25/64” (A) x 25/32” (A)

Weight : 

140g (4.9 oz) without batteries / 163g  (5.7oz) with batteries

DEVICE SPECIFICATIONS

Frequency : 

 2.4 GHz frequency range 

Connection Range : 

The operating range is up to 10 meters (32.8 feet) 

NOTE :

 Connection range is affected by many factors, such as nearby metallic  

 

objects and the relative positioning of the device and the receiver.

BLUETOOTH SPECIFICATIONS

NOTE: All specifications are subject to change without notice.

 

Never continue to use the Calculator Keypad if it starts to smoke, emits a strange 

odor, or emits heat. Continued use of the calculator under such conditions creates 

the danger of fire and electric shock. 

 

When cleaning the Calculator Keypad, do not use a damp cloth or volatile liquid 

such as paint thinner; instead, use only a soft, dry cloth. 

 

Never dispose of the Calculator Keypad improperly (such as burning), which can 

lead to personal injury or harm. You should dispose of this product in accordance 

with Federal, State, and Local regulations.

HANDLING AND CARE

Screens or set-up may vary depending on the computer or Bluetooth device driver.

Instructions are provided for Windows

®

 XP, Windows Vista

®

, Windows

®

 7 and Macintosh.

INITIAL SETUP INSTRUCTIONS

1.  Remove the battery cover from the back of the Calculator Keypad by sliding the 

cover in the direction of the arrow. 

2.  Install AAA alkaline batteries, matching the positive (+) and negative (–) ends  

of each battery with the polarity indicators inside the battery compartment.

3.  Place the battery cover back on the battery compartment.

CAUTION: 

There is a risk of explosion if an incorrect battery type is installed. 

 

Please dispose of used batteries according to their instructions.

BATTERY INSTALLATION

1

2

3

 

Power on

 

Clear all display   |   Keypad lock / unlock

 

Re-connect the Bluetooth connection

 

Clear last input entered   |   Clear all input  

(CAL mode only)

 

Escape the input 

(KP mode only)

 

Switch between Calculator Mode or Keypad Mode

 

Backspace in Keypad mode; in Calculator mode shifts each digit of the 

displayed numerical value and clears the last significant digit

 

Send calculation results or display contents to computer  

(CAL mode with Bluetooth Connection)

 

Perform percentage add-on and discount calculation.

 (CAL mode only)

 

 

Execute calculation

 (CAL mode only)

 

▪ Enter Key -- Confirm the input 

(KP mode only)

 

Set the number of digits displayed in calculation after the decimal point

 

Press 

 and then press and hold 

, the display will change in the 

sequence of  F 

 0 

 2 

 3 

 F 

(CAL mode only)

 

▪ F represents a floating decimal point

WAKE

UP

KEY INDEX

 

J

The Bluetooth icon (

will flash 

on and off during the setup  

connection process.

 

J

Once the device is successfully 

connected to your computer, 

the Bluetooth icon (

on the 

front display will remain solid.

BLUETOOTH ICON

© CANON ELECTRONIC BUSINESS MACHINES (H.K.) CO., LTD. 2011

CALCULATOR MODE AND KEYPAD MODE

When Bluetooth connected, this Calculator Keypad has 2 modes --  

Calculator Mode (CAL) and Keypad Mode (KP).

Switch between Calculator and Keypad Mode

 

J

To switch between Calculator and Keypad mode,  

simply press the           key. 

Calculator Mode 

(with Bluetooth connection)

 

J

The calculator performs normal 10-digit calculator operations.

 

J

Send calculation results or display contents to a computer by pressing 

SEND

.

• 

You cannot perform a send operation while the E (Error) indicator is shown on 

the Calculator Keypad display.

• 

The 

SEND

 key is disabled when the calculator is not Bluetooth connected.

Keypad Mode

 (with Bluetooth connection)

 

J

Input the following to a computer directly: 

Numbers 0-9 + – × ÷

Auto Power Off and Wake-up

 

J

Calculator Only, NOT Bluetooth Connected

• 

The device will automatically power off after approximately 7 minutes  

of inactivity. 
Press the 

 key to turn on the device.

 

J

CAL and KP Modes, with Bluetooth Connection

• 

The Bluetooth connection will be disconnected after approximately 30 minutes 

of inactivity (the display will reset to “0”). The device will function the same as 

Calculator Only, NOT Bluetooth Connected

”.

Press 

 to re-activate the Bluetooth connection.

• 

After the Bluetooth connection is disconnected, the device will automatically 

power off after an additional 7 minutes of inactivity. Press 

 and then 

 

to turn on the device and re-activate the Bluetooth connection.

Power-low Indicator

 

J

When the display is dim or the 

 icon appears, 

replace the batteries to avoid running out of 

power unexpectedly.

Keypad Lock

 (with Bluetooth connection)

 

J

Press the 

 key and hold for 3 seconds to lock. 

 

J

To unlock, press the 

 key and hold for 3 seconds.

Keypad mode display

Power-low display

Keypad locked display

1

Your computer is now setup to use your Calculator Keypad.

Click “

Quit

” in the Conclusion window to finish.

(NOTE: If Keyboard Setup Assistant appears, ignore, and close the window.)

8

Press the “

PAIR

” button on 

the device using the tip of a  

pen or a similar object.

(NOTE: In the Bluetooth Setup Assistant, the “Canon X Mark I K”  

should appear under the Devices list. If not, wait a moment  

and press the “PAIR” button again.)

4

Move the Bluetooth switch on 

the device to “

MAC ON

”.

(NOTE: The   icon 

on the front display  

should be flashing.)

3

Select “

Canon X Mark I K

” and click “

Continue

”.

5

Switch to 

Keypad mode

 by pressing 

,   will appear on the display.

6

Enter the 

passkey

 on the 

keypad and press 

.

(NOTE: Must be in Keypad 

mode to enter passkey.)

7

To activate Bluetooth,

go to the Bluetooth icon in  

the menu bar and select  

Turn Bluetooth On

”.

(NOTE: If already “On”, skip to step 2.)

Go to the Bluetooth icon and select 

Set up Bluetooth Device...

to open the Bluetooth Setup Assistant.

2

MACINTOSH

®

Enter the 

passkey

 or 

code

 

on the keypad and press 
 

.

(NOTE: Must be in Keypad 

mode to enter code.)

6

Your computer is now setup to use your Calculator Keypad.

(NOTE: The Bluetooth Setup window should automatically close once 

the passkey or code is accepted.)

7

1

Open “

My Bluetooth Places”

 and double-click on “

Add a Bluetooth 

Device

” to open the Bluetooth Setup.

Press the “

PAIR

” button on 

the device using the tip of a  

pen or a similar object.

(NOTE: In the Bluetooth Device Selection window, “Canon X Mark I K” 

should appear. If not, wait a moment and press the “PAIR” button  

again -or- move the Bluetooth switch to “OFF” and then to “PC ON”, 

click “Search Again” and press the “PAIR” button again.)

3

Select “

Canon X Mark I K

” and click “

Next

”.

(NOTE: If asked, “Do you need a passkey to add your device?”,  

select “Choose a passkey for me” and click “Next”.)

4

2

To make the device 

discoverable, move the 

Bluetooth switch on the  

device to “

PC ON

”, then

click “

Next

” on the computer.

(NOTE: The   icon 

on the front display  

should be flashing.)

Switch to 

Keypad mode

 by pressing           ,   will appear on the display.

WINDOWS

®

 XP

Reviews: