cantaloupe ePort G10-S Quick Start Manual Download | Manualshive

Page: 1 / 8

background image

TOOLS REQUIRED FOR INSTALLATION

11/32” Socket

1/4” Socket

12” Extension

Ratchet

Phillips Screwdriver

Wire Cutters

Power Drill*

3/16” & 3/8” Drill Bit*

Multi-diameter Step Drill Bit,

1/4”-3/4”*

#VVXUD0101912

* Required for surface-mount installations

Thank you for your purchase. Before you start, please read these instructions thoroughly,

and then take a few moments to plan your installation.

You must have a signed ePort Connect Services Contract and a bank account assigned to

this device for it to be able to accept credit card transactions. Please call USA Technologies

Customer Care at 1.888.561.4748, if you need activation documents.

G10-S Telemeter

Card Reader

CANTALOUPE

1
2
3
...
»

Summary of Contents for ePort G10-S









Reviews:

No comments

Related manuals for ePort G10-S

Brand: H&S Pages: 36

MIPort Universal PCI Cards 3PCIOU1

Brand: B&B Electronics Pages: 92

Brand: NCR Pages: 6

Brand: Kobo Pages: 11

Brand: Alpine Pages: 82

Brand: Rocstor Pages: 2

Brand: Yarvik Pages: 20

Brand: Datalogic Pages: 20

Brand: ICS Advent Pages: 34

Brand: Casio Pages: 60

Brand: Pyle Pages: 12

Brand: Radio Shack Pages: 64

Brand: Phonocar Pages: 16

Brand: Honeywell Pages: 44

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands