background image

1

CIRCUIT BREAKER

(Trip breaker for The

circuiT you will be

working on)

FUSE BOX

(remove fuse for The

circuiT you will be

working on)

18

84

70

  The  blades  in  each  pack  are  matched  for  equal 

weight  to  assure  smooth  fan  operation.  If  more 

than one fan is being installed, be careful not to 

mix blades from different cartons.

  Inspect the contents of your carton for possible 

shipping or handling damage and report any such 

damage  directly  to  your  authorized  Casablanca 

dealer.

  It is always a good idea to have an assistant to 

help with the installation.

  When cleaning, painting, or working near your fan, 

be very careful of the fan and blades. Always turn 

the power OFF to the ceiling fan before servicing 

it, working on it, or replacing light bulbs. 

  Never  insert  anything  into  the  path  of  the  fan 

blades while the fan is in operation.

•  Never install a fan over a pool or spa. 

  Never operate a fan that has been damaged in any 

way. Contact Casablanca Fan Company by calling 

toll  free  1-888-227-2178,  or  contact  your  local 

authorized  Casablanca  dealer  for  assistance  in 

obtaining service.

CONTENTS

READ AND SAVE THESE INSTRUCTIONS

SAFE USE

Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product 

and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this 

owner’s manual completely and carefully. Retain this manual for future reference.

SAFETY FIRST

INTRODUCTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1

mOUNTINg RECOmmENDATIONS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

FAN INSTALLATION   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

CONTROL FEATURES:

  INTELI•TOUCH2 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    TROUbLEsHOOTINg INTELI•TOUCH2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

 

BEFORE YOU START

PN 4843010   AT0109

cauTion: To avoid possible electrical shock, make certain that electricity is turned off at 

the circuit breaker or fuse box before attempting any installation procedure.

• 

CAUTION: RISK OF ELECTRICAL SHOCK!  All wiring must be performed in accordance with national and local electrical 

codes.  If you are unfamiliar with the wiring codes, you should use a qualified electrician.  To avoid overheating and 

possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated 

appliance, or transformer-supplied appliance..

•  This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan 

installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling 

installations.

• 

This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum 

current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light 

current is 2.8 amps or 340 watts of lighting.

  Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make 

sure all wires are within the canopy and that no wires are being pinched.

For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories.

Summary of Contents for 64xxT














Reviews: