background image

1

FUSE BOX

(Remove fuse foR the

ciRcuit you will be

woRking on)

18″

84″

70″

CONTENTS

INTRODUCTION 

1

mOUNTINg ReCOmmeNDaTIONs 

2

faN INsTaLLaTION 

3

OpTIONaL exCLUsIve LIghT fIxTURe INsTaLLaTION 

9

CONTROL feaTURes:
 

Versa•Touch 2 

11

 

TROUbLeshOOTINg 

13

PN 8643520   AT1008

BEFORE YOU START

NOTES

READ AND SAVE THESE INSTRUCTIONS

safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product 

and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this 

owner’s manual completely and carefully. Retain this manual for future reference.

SAFETY FIRST

CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the 

circuit breaker or fuse box before attempting any installation procedure.

•  cauTIoN: rIsK oF eLecTrIcaL shocK!  all wiring must be performed in accordance with national and local elec-

trical codes.  If you are unfamiliar with the wiring codes, you should use a qualified electrician.  To avoid overheating and 

possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated 

appliance, or transformer-supplied appliance.

•  This fan is designed to be installed on an existing electrical outlet box. The outlet box must be uL Listed for ceiling fan 

installations, if it is not, a new box must be installed. casablanca extension poles are available for sloped or high ceiling 

installations.

•  This ceiling fan requires a grounded electrical supply of 120 Vac, 60 hz and a minimum 15 amp circuit. The maximum 

current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light 

current is 2.8 amps or 340 watts of lighting.

•  Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make 

sure all wires are within the canopy and that no wires are being pinched.

For best performance and for your warranty to be valid, 

use only genuine Casablanca blades, light fixtures, and accessories.

•  The blades in each pack are matched for equal 

weight  to  assure  smooth  fan  operation.  If 

more than one fan is being installed, be careful 

not to mix blades from different cartons.

•  Inspect  the  contents  of  your  carton  for 

possible  shipping  or  handling  damage  and 

report  any  such  damage  directly  to  your 

authorized casablanca dealer.

•  It is always a good idea to have an assistant 

to help with the installation.

•  When  cleaning,  painting,  or  working  near 

your fan, be very careful of the fan and blades. 

always turn the power Off to the ceiling fan 

before servicing it, working on it, or replacing 

light bulbs. 

•  Never insert anything into the path of the fan 

blades while the fan is in operation.

•  Never install a fan over a pool or spa. 

•  Never operate a fan that has been damaged in 

any way. Contact Casablanca fan Company by 

calling 1-888-335-5247, or contact your local 

authorized casablanca dealer for assistance 

in obtaining service.

CIRCUIT BREAKER

(tRip bReakeR foR the

ciRcuit you will be

woRking on)

Summary of Contents for Wilderness















Reviews: