1
1
8
9
MODE
!
L(mm)
12 x1.75
935
14 x 1.50
1020
14 x 1.75
1055
16 x 1.50
1185
16 x 1.75
1195
18 x 1.50
1340
18 x 1.75
1350
20 x 1.75
1515
20 x 1-3/8
1615
22 x 1-3/8
1770
22 x 1-1/2
1785
24 x 1
1753
24 x 3/4 Tubular
1785
24 x 1-1/8
1795
24 x 1-1/4
1905
24 x 1.75
1890
24 x 2.00
1925
24 x 2.125
1965
26 x 7/8
1920
26 x 1(59)
1913
26 x 1(65)
1952
26 x 1.25
1953
26 x 1-1/8
1970
26 x 1-3/8
2068
26 x 1-1/2
2100
26 x 1.40
2005
26 x 1.50
2010
26 x 1.75
2023
26 x 1.95
2050
26 x 2.00
2055
26 x 2.10
2068
26 x 2.125
2070
26 x 2.35
2083
26 x 3.00
2170
27 x 1
2155
27 x 1-1/8
2161
27 x 1-1/4
2161
27 x 1-3/8
2169
650 x 35A
2090
650 x 38A
2125
650 x 38B
2105
700 x 18C
2070
700 x 19C
2080
700 x 20C
2086
700 x 23C
2096
700 x 25C
2105
700 x 28C
2136
700 x 30C
2170
700 x 32C
2155
700C Tubular
2130
700 x 35C
2168
700 x 38C
2180
700 x 40C
2200
L mm
SET
ST/STOP
MODE
SET
OK
OK
Warning
• Pay attention to the road or trail! Do not be distracted by the
computer.
• Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws are not loosen.
• Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
• Avoid unnecessary prolonged exposure to the sun. Never at-
tempt to disassemble the computer head.
• Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
Computer Set-up
(For first use or after replacing the battery)
All Clear
Push the AC button on the backside.
* Push the AC button when using this
system for the first time and every
time the battery is replaced.
1
Set The Tire Circumference
Set the tire circumference in mm.
Note
Refer to the chart shown on the right.
Setting is fixed and completed by pushing the SET button.
3
Increase the
number
Max. 2999 mm
Decrease
the number
Min. 10 mm
MODE Button
START/STOP Button
SET Button
Contact Point
Measurement Selection
Select the measurement unit, kilometer or mile, by pushing the
MODE button. And fix it by pushing the SET button.
2
Kilometer
Mile
AC Button
You need to know the
tire circumference
(L mm) beforehand.
You can refer to the
guide chart to roughly
know the tire circum-
ference.
Tire size
Tire size is usually shown on
the sidewall of tires.
Important
Note
Basic Functions Test
Spin the front wheel to see if Speed is reading properly. Push the mode button until Cadence
(Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading
properly.
Note
When the computer does not indicate the speed/cadence, check the position of the
magnet and the sensor.
Lever
Mount The Bracket
Secure the cord on the frame or the fork with the nylon ties
9
and coil it around the brake
cable to lead to the handle bar.
Put the rubber pad
8
on the bracket
1
and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket until you hear the click sound. The contact
points are automatically closed. When you need to remove the computer, slide forward the
computer with the lever pushed simultaneously.
Note
Allow enough wire clearance in the area marked with
to insure you can turn
the handlebars all the way from side to side without pulling the wire.
4
3
Slide
Rotate the front wheel.
Rotate the crank arm
AC Button
Preparation Complete.
(the screen will show the time measurement in this state)
* The auto mode is ON in this state.
®
7
4
1
2
6
7
3
4
5
8
9
3
9
3
6
7
4
7
9
6
3
7
4
ASTRALE8
6
3
2
1
Installation of the Computer on Your Bike
The computer comeswith the following parts.
Important Note
Mount the magnets
6
(
7
) and the sensors
3
(
4
) on the appropriate positions so that
the center of each magnet
6
(
7
) may align with the the marked line on the sensor
when the front wheel (or the crank arm) is rotated.
1
Bracket
2
Cord
3
Speed Sensor
(short cord)
4
Cadence Sensor
(long cord)
Center
5
Sensor Rubber Pad
6
Wheel Magnet
7
Cadence Magnet
8
Bracket Rubber Pad
9
Nylon Ties (12)
Left Chain
Stay
2
1
Please read these instructions carefully before installing or
using the CAT EYE ASTRALE 8.
Please don’t throw away this manual, Keep the manual at a place easily accessible.
CAT EYE ASTRALE 8
CYCLOCOMPUTER CC-CD200
E: Owner’s Manual
Spoke
Crank Pedal
Front Fork
Sensor Side
Within 5 mm
Inward Side of
The Crank Arm
Left Chain Stay
Mount the cadence magnet and cadence sensor.
• Mount the cadence magnet
7
on the crank arm so that it faces the sensor.
• Secure the cadence sensor
4
on the left chain stay with the nylon ties
9
.
Mount the wheel magnet and speed sensor
• Mount the wheel magnet
6
on a spoke of the front wheel so the surface of the magnet
will face the sensor.
• Secure the speed sensor
3
on the front fork with the larger nylon ties
9
.
Sensor Side
Important Note
Adjust the position of each sensor so they are within 5mm of the
6
(
7
) magnet.
Secure the nylon ties.
Marked Line
Marked Line
Center
Front Fork
Within 5 mm
Rotate
Rotate
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002 CAT EYE Co. Ltd.
CCMCD2-021210 066600250
1
