www.interphone.cellularline.com
www.interphone.cellularline.com - www.cellularline.com
Export Dept. international.interphone@cellularline.com
QUICK GUIDE
EN
Functions
This user’s manual has referred to the latest information we had when this user’s
manual was made. The screen display and illustrations are used in this user’s manual
for the purpose of introducing details of this digital camera in a more specific and
direct way. Difference may arise between these displays and illustrations and
the digital camera actually available for you due to difference in technological
development and production batch, under which case, the actual functions of this
video camera shall prevail.
Announcements
Please read the Announcements carefully before using this video camera for
proper and safe operation, so as to bring its optimum performance into play and
extend its service life.
- Do not expose the video camera to sunshine directly, nor point its lens to sunlight.
Otherwise, the image sensor of the video camera may be damaged.
- Take good care of the video camera and prevent water or sand particles from
entering the video camera when it is used on the beach or water, because water,
sand particles, dust or component containing salt may damage the video camera.
- Keep the video camera contaminated free of dust and chemical materials. Place it
in a cool, dry and well ventilated place. Do not place the video camera in a high
temperature, moist or dusty place.
- Please check if the video camera can operate normally before use.
- If dirt or stain is accumulated on the video camera or on its lens, use soft, clean
and dry rag to wipe it away gently. If the video camera or its lens is stained with
sand particles, blow them away gently. Do not use cloth to wipe arbitrarily.
Otherwise, it may scratch the surface of video camera or its lens.
- If it is required to clean camera surface, firstly blow away the sand dust
accumulated on this surface, and then wipe the camera gently with rag or tissue
applicable to optical equipments. Please use the cleaning agent of video camera
for wiping if necessary. Do not use organic solvent to clean the video camera.
- Do not touch the lens surface with fingers.
- Please back up the data if the memory card inside this video camera is used for
the first time.
- The externally installed memory cards are manufactured from precise electronic
components. Data may be lost or damaged under the following circumstances:
1. Improper use of the memory card.
2. The memory card is bent, dropped or collided.
3. Place it under high temperature or moist environment or expose to sunshine
directly.
4. Electrostatic or electromagnetic field exists around the memory card.
5. This memory card is taken out or power supply is interrupted when this video
camera or computer is connected to the memory card (i.e. during reading,
writing and formatting).
6. Touch the metal contact surface of the memory card with fingers or metal materials.
System Requirements
System Requirements
Operating
System
Microsoft Windows2000, XP, Vista, 7
CPU
Intel Pentium III of more than 800MHz or other CPU with
equivalent performance
Internal Memory Larger than 512MB
Sound Card and
Display Card
The sound card and display card shall support DirectX8 or
higher version.
CD Driver
Speed of 4 times or faster
Hard Disk
Free space of more than 500MB
Others
One standard USB1.1 or USB2.0 port
Introduction to Appearance and Keypad
(1) Memory card slot
(2) Reset
(3) USB slot
(4) Power button
(5) MIC
(6) Shutter button
(7) Mode Switch
(8) Lens
(9) LCD TFT
(10) Working Indicator Light
(11) Indicator Light for charging
(12) Wrist strap eyelet
Usage
1. Charge the built-in lithium battery
Connect the video camera with computer for charging in the shutdown state.
The indicator light for charging is on at this time and will be off after charging. In
general, it can be fully charged after 2-4 hours.
2. Use of Memory Card
2.1 Push the memory card into the card slot according to the concave lettering
beside the slot of memory card till it is completely inserted.
2.2 To take out the memory card, gently press the end of the memory card inward
and it will pop up.
Note: No built-in memory is available in this video camera. Make sure to insert
memory card before using.
3. Startup/Shutdown
3.1 Startup: Press the POWER button for 3 seconds, the screen is displayed and the
camera is on.
3.2. Shutdown: Press the POWER Key, and the camera will be shut down.
Automatic shutdown: when the idle time of the video camera reaches the time
for automatic shutdown, it will be shut down automatically to save power. The
default time of this camera for automatic shutdown is 5 minutes.
Indicator Light
for charging is on
USB Cable
MOTIONCAMminiLCD for bike
