RED
WHITE
WHITE
GREY
WH
WHITE
E
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing
door control.
• Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from
a closing garage door:
• Install door control within sight of garage door, out
of reach of children at a minimum height of 5 feet
(1.5 m), and away from ALL moving parts of door.
• NEVER permit children to operate or play with door
control push buttons or remote control
transmitters.
• Activate door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to
door travel.
• ALWAYS keep garage door in sight until completely
closed. NEVER permit anyone to cross path of
closing garage door.
PUSH BUTTON DOOR CONTROL
Model 883LM
TO ADD, REPROGRAM, OR CHANGE A REMOTE
CONTROL/KEYLESS ENTRY PIN USING THE
DOOR CONTROL
NOTICE: To comply with FCC and or Industry Canada rules (IC),
adjustment or modifi cations of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or offi ce use.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
For use with Security
✚
2.0
TM
Garage Door Openers. All
Security
✚
2.0
TM
Garage Door Openers have a yellow
Learn button and a yellow antenna wire.
1
Unplug the garage door opener.
4
6
7
3
Connect the wire to the red and white
terminals on the garage door opener.
Reconnect power to the garage door
opener. The LED behind the Push button on
the door control will blink if installed
correctly.
Mount the door control with the hardware
provided.
Connect one wire to each of the two screws
on the back of the door control. The wires
can be connected to either screw.
PRE-WIRED INSTALLATIONS:
Choose any two
wires to connect, but make note of which wires
are used so that the correct wires are connected
to the garage door opener.
1
Press and hold the Light button and the Push
button until the Push button LED begins to
blink.
The garage door opener lights will flash (or two
clicks will be heard) when the code has been
programmed.
Press the button on the remote control that
you wish to operate your garage door.
PIN
?
?
?
?
1
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PRS
8
TUV
9
WXY
0
QZ
*
#
ENTER
0 QZ
*
#
ENTER
OR
2a
Enter a 4-digit personal identification number
(PIN) of your choice on the keyless entry
keypad. Then press the ENTER button.
2b
Light Button
Push Button
2
5
Strip 1/4" (6 mm) of insulation from one
end of the wire and separate the wires.
Strip 7/16" (11 mm) of insulation from the
other end of the wire near the garage door
opener.
Installation
Programming
To insert or release wire, push in
tab with screwdriver tip.
Run the white and red/white wire from the
door control to the garage door opener.
Attach the wire to the wall and ceiling with
the staples (if applicable).
Do not pierce the wire
with the staple as this
may cause a short or an
open circuit.
8
9
To synchronize the door control to the
garage door opener, press the push button
until the garage door opener activates (it
may take up to 3 presses). Test the door
control by pressing the push button, each
press of the push button will activate the
garage door opener.
7/16" (11 mm)
1/4" (6 mm)
