background image

FEATURES

• Automatically comes on when motion is de-

tected.

• Automatically turns light off.

• Photocell keeps the light off during daylight 

hours.

UNPACKING

Be sure to remove all contents from packaging 

and verify all items are present before assembling 

this light fixture. This package includes the fol-

lowing items:

• Lantern

• Mounting Bracket (Mounting Bracket Screws 

Are Not Included - Use 4mm dia. (8G) x 30 mm 

Wood Screws)

• Owner’s Manual

REQUIREMENTS

• The light control requires 230 volts AC.

• If you want to use Manual Mode, the control 

must be wired through a switch.

• It is illegal for persons other than a licensed 

electrician or person authorized by legislation 

to work on fixed wiring or other electrical 

installations.

Before installation, record the model num-

ber listed inside the fixture. Attach receipt 

in case of possible warranty issues.
Model Number:

© 2011 The Chamberlain Group, Inc 

201102-01A

Motion Sensing 

Diecast Lantern

Lantern*

*Note:

 Illustrations are for reference only and may 

be different from actual product

Installation and Operating Instructions

Models: SH-9191AU, SH-9192AU, 

and SH-9194AU

®

TM

Summary of Contents for Secure Home SH-9191AU









Reviews: