To reduce the risk of SEVERE INJURY to persons:
• DO NOT enable the Smart Garage™ Control if operating either one-piece or
swinging doors. Enable this device with sectional doors ONLY.
If using the Smart Garage Control with residential door openers, the Control
must be used only with door openers manufactured after 1993 that use
photoelectric sensors located near the bottom of the door track.
WARNING:
This product can expose you to chemicals including lead, which
are known to the State of California to cause cancer or birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov
Compatible with:
Smart Garage
TM
Control
All versions of:
• MYQ-G0401
• 821LMC
myQ
®
Smart Garage
TM
Hub
All versions of:
• MYQ-G0301
• 821LMB
SMART GARAGE
CONTROL HUB
Amber LED
TO ADD A NEW DOOR SENSOR TO A SECOND
GARAGE DOOR OPENER GO TO THE myQ APP
TO REPLACE AN EXISTING DOOR SENSOR
1
.
Press the existing Door Sensor test button. Recall
if the Hub beeps once or twice. This is the number
for your existing Door Sensor.
2
.
On the Hub, press and release button 1 for door 1 or
button 2 for door 2. The Hub’s amber LED will turn on.
3
.
Remove the pull tab from the new Door Sensor
to activate the battery.
4
.
On the new Door Sensor, press and release the
Test button. The Hub will fl ash and beep indicating
successful programming.
5
.
Mount Door Sensor (instructions to the right).
6
.
In the myQ App, check that you can open and close
your garage door to confi rm successful programming.
NOTICE:
This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device. This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
TEST DOOR SENSOR BATTERY
Test your Door Sensor every 6 months or if the myQ system is not working as expected.
Press and release the test button on the Door Sensor, the LED on the Door Sensor should
blink and the Hub should beep. Wait 5-10 seconds, then repeat this test 5 more times
(wait 5-10 seconds between each test). If the LED doesn’t blink or the Hub doesn’t beep
with each press, replace the battery in the Door Sensor.
Replacement Part: K010A0056 Door Sensor 3V Battery, CR2450.
One Year Limited Warranty:
The Chamberlain Group, Inc. warrants to the fi rst consumer purchaser of this product that it is free
from defect in materials and/or workmanship for a period of 1 year from the date of purchase.
SMART GARAGE
™
CONTROL DOOR SENSOR
QUICK START GUIDE
MYQ-G0402 AND 821LMC-SENSOR
NOTE:
Your Hub has the capacity to program two Door Sensors.
This Sensor can either be added to a second Garage Door Opener
or replace an existing inoperable Door Sensor.
myQ Garage
TM
All versions of:
• MYQ-G0201
• 821LM
LED
Pull Tab
Test
Button
Door 1
Door 2
HUB
DOOR SENSOR
114-5361-000B
Hook
and Loop
Adhesive
Strips
OR
Pry with coin
A.
B.
PRODUCT HELP
MOUNT DOOR SENSOR
Install the new Door Sensor (top facing up) with the included fastening strips (A.)
or optional screws (B.) to a clean, dry area on top panel of garage door as shown.
Chamberlain.com/smart-garage-control/manual
LiftMaster.com/smart-garage-control/manual
© 2020, The Chamberlain Group, Inc. | All Rights Reserved | Tous droits réservés | Todos los derechos reservados
114-5361-000B
