background image

 

Installation, Operating and 

Maintenance Instructions 

 

90/4.5.5 

Rev. 0 

 

 

    

 

 

Constantemp Double Wall Low pressure steam-water Heater 

F-340LDW,F-640LDW, F-940LDW and F-1240LDW 

 

Table of Contents 

SECTION I ................................................................................................................................................................................... 2

 

INSTALLATION....................................................................................................................................................................... 2

 

OPERATION ............................................................................................................................................................................. 2

 

SECTION II.................................................................................................................................................................................. 2

 

START-UP PROCEDURE ........................................................................................................................................................ 2

 

TO DRAIN UNIT FOR PROLONGED SHUT-DOWN ........................................................................................................... 3

 

SECTION III ................................................................................................................................................................................ 7

 

MAINTENANCE OF SYSTEM COMPONENTS.................................................................................................................... 7

 

ACTUATOR ASSEMBLY........................................................................................................................................................ 2

 

VALVE PLUG ASSEMBLY..................................................................................................................................................... 2

 

CONTROL VALVE ASSEMBLY ............................................................................................................................................ 2

 

MAINTENANCE OF SYSTEM COMPONENTS HEAT EXCHANGER............................................................................... 2

 

SECTION IV - TROUBLE SHOOTING GUIDE ..................................................................................................................... 2

 

Recirculating Systems ................................................................................................................................................................ 2

 

Heat Exchanger and Blending Valve ......................................................................................................................................... 3

 

 

Table of Figures 

FIGURE 1 ..................................................................................................................................................................................... 4

 

FIGURE 2 ..................................................................................................................................................................................... 6

 

Figure 3 ......................................................................................................................................................................................... 2

 

Figure 5 ......................................................................................................................................................................................... 2

 

Figure 6 ......................................................................................................................................................................................... 2

 

F-340LDW .................................................................................................................................................................................... 2

 

F-640LDW .................................................................................................................................................................................... 3

 

F-940LDW .................................................................................................................................................................................... 4

 

F-1240LDW .................................................................................................................................................................................. 5

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Leslie F-1240LDW




















Reviews: