background image

Rack-Mount and Ground the Chassis

Unpack and Inspect the Chassis, on page 1

Rack-Mount the Chassis Using Brackets, on page 2

Rack-Mount the Chassis Using Slide Rails, on page 4

Ground the Chassis, on page 9

Unpack and Inspect the Chassis

Keep the shipping container in case the chassis requires shipping in the future.

Tip

The chassis is thoroughly inspected before shipment. If any damage occurred during transportation or any
items are missing, contact your customer service representative immediately.

Note

See

Package Contents

for a list of what shipped with the chassis.

Step 1

Remove the chassis from its cardboard container and save all packaging material.

Step 2

Compare the shipment to the equipment list provided by your customer service representative. Verify that you have all
items.

Step 3

Check for damage and report any discrepancies or damage to your customer service representative. Have the following
information ready:

• Invoice number of shipper (see the packing slip)

• Model and serial number of the damaged unit

• Description of damage

• Effect of damage on the installation

Rack-Mount and Ground the Chassis

1

Summary of Contents for Firepower 2100 Series













Reviews: