background image

C H A P T E R

   

2-1

Installing Cisco Intrusion Prevention System Appliances and Modules 5.1

OL-8677-01

2

Installing IDS-4210

This chapter describes IDS-4210 and how to install it and its accessories.

Note

IDS-4215 replaced IDS-4210, which is no longer sold.

Note

If you purchased an IDS-4210 before July 2003, you must upgrade the memory to 512 MB to install 
Cisco IPS 5.x. for more information, see 

Upgrading the Memory, page 2-3

Note

IDS-4210 does not support inline (IPS) mode. 

Caution

The BIOS on IDS-4210 is specific to IDS-4210 and must only be upgraded under instructions from Cisco 
with BIOS files obtained from the Cisco website. Installing a non-Cisco or third-party BIOS on 
IDS-4210 voids the warranty. For more information on how to obtain instructions and BIOS files from 
the Cisco website, see Obtaining 

Obtaining Cisco IPS Software, page 11-1

.

This chapter contains the following sections:

Front and Back Panel Features and Indicators, page 2-2

Upgrading the Memory, page 2-3

Installing IDS-4210, page 2-5

Installing the Accessories, page 2-7

Summary of Contents for IDS 4210 - Intrusion Detection Sys 4210 Sensor













Reviews: