background image

Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

 

© 2006, 2007, 2008 Cisco Systems, Inc. All rights reserved.

Cisco PVDM2-12DM, PVDM2-24DM, and 
PVDM2-36DM Digital Modem Packet Voice Data 
Modules

First Published: June 19, 2006
Last Updated: July 11, 2008

The Cisco digital modem packet voice data modules (Cisco PVDMs), type 2 (Cisco PVDM2s), are 
high-density PVDMs containing 12, 24, or 36 digital modems. These modems provide direct digital 
connection to Integrated Services Digital Network (ISDN) Primary Rate Interface (PRI) channels, to 
Basic Rate Interface (BRI) channels, and to channel associated signaling (CAS) digital trunk lines. The 
PVDM2s are installed in Cisco 2800 series and Cisco 3800 series integrated services routers.

Finding Feature Information in This Module

Your Cisco IOS software release may not support all of the features documented in this module. To reach 
links to specific feature documentation in this module and to see a list of the releases in which each feature is 
supported, use the 

“Feature Information for Digital Modem PVDM2s” section on page 47

.

Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and software image 
support. To access Cisco Feature Navigator, go to 

<http://www.cisco.com/go/cfn>

. An account on Cisco.com 

is not required.

 

Contents

Prerequisites for Cisco Digital Modem PVDM2s, page 2

Restrictions for Cisco Digital Modem PVDM2s, page 3

Information About Cisco Digital Modem PVDM2s, page 4

How to Configure Digital Modem PVDM2s, page 4

Configuration Examples for Digital Modem PVDM2s, page 22

Additional References, page 25

Summary of Contents for PVDM2 24DM - Digital Modem Module

















































Reviews: