background image

4.6  Error Indication

The following LED indications are added to CT-S4000L/CT-S4000DCL.

LINE THERMAL PRINTER

MODEL CT-S4000L/CT-S4000DCL

User’s Manual

Contents

1.1

Features

4.6

Error Indications

5.3

Manual Setting of Memory Switch

5.4

Selecting Paper Type

5.5

Adjusting Paper Sensor

5.6

Printing Paper

1.1  Features

High-speed printing at a maximum of 120 mm/sec

2-dimensional barcode

Label of nonstep 58 to 105 mm wide as well as 112 mm is usable

Paper sensor sensitivity adjustment by variable resistor is adopted.

Status

POWER LED

ERROR LED

Buzzer

Wait for cutting label

OFF

Paper detection error

OFF

Memory Switch

Function

0 (OFF)

1 (ON)

SW4-4

Paper Select

Thermal Roll

BM.P/Lbl.P *

SW4-5

Position detect

Black Mark

Label

* The Print Width 660 dots is not available for printing a label paper.
* The memory switches SW2-8 will be ignored for Label.

5.3  Manual Setting of Memory Switch

Functions of memory switches SW4-4 and SW4-5 of CT-S4000L/CT-S4000DCL are as
shown below. (The 

 white-on-black characters 

 are factory setting.)

5.4  Selecting Paper Type

Paper type selection is available by the combination of memory switches SW4-4 and
SW4-5 by the used of “Memory Switch Select Mode”. In addtion, the following
procedure is available.

1 Enter Selecting Paper Type mode.

1)Open the printer cover and remove paper.  Pressing and holding the 

FEED button

,

turn the printer power ON.  The POWER LED starts blinking.

2)Release the 

FEED button

 and then close the printer cover.  Buzzer sounds and

the paper type currently set is indicated by the LED on the operation panel.

2 Select Paper Type.

Press the 

FEED button

 to match the paper type loaded to the LED indications in the

table below. (Refer to the table below.)

Refer to CT-S4000/CT-S4000DC User’s Manual of standard model when reading this manual.

Green lit

(OFF)

(OFF)

Red lit

Green lit

Red lit

Label

Thermal paper roll

Black Mark paper

POWER LED

ERROR LED

CITIZEN is a registered trade mark of Citizen Holdings Co., Japan

CITIZEN es una marca registrada de Citizen Holdings Co., Japón

Company names and product names in this manual are trademarks or

registered trademarks of relevant companies.

Copyright c  2007 by 

CITIZEN SYSTEMS JAPAN CO., LTD.

Summary of Contents for CT-S4000DCL

Page 1: ...n black characters are factory setting 5 4 Selecting Paper Type Paper type selection is available by the combination of memory switches SW4 4 and SW4 5 by the used of Memory Switch Select Mode In addtion the following procedure is available 1 Enter Selecting PaperType mode 1 Open the printer cover and remove paper Pressing and holding the FEED button turn the printer power ON The POWER LED starts ...

Page 2: ...tion where LED begins to change from orange to green Label light emitting sensor Label light receiving sensor Black Mark sensor While turning the adjuster by the screwdriver do not let the part of the screwdriver touch the metal frame Otherwise proper LED light color will not be displayed while touching 4 Perform Paper Measuring operation When the FEED button is pressed label is fed and paper meas...

Page 3: ...aper sensor must be carried when the type of liner is changed Mark Item Dimensions A Liner width 58 to 112 B Label width 54 to 108 0 5 C Left edge of label 2 0 5 D Print width 50 to 104 E Top margin 2 1 F Print length 21 to 296 G Bottom margin 2 1 H Cut position between labels 1 2 x Size I I Gap between labels 4 to 30 J Label length 25 to 300 K Label pitch I J Unit mm _ _ _ 0 1 In the case of memo...

Page 4: ... value of black mark must be 0 9 or more When using the black mark paper consider the margin of 2 mm for the print position against the standard position and 5 mm for print length Refer to the above drawing for the printable area and have enough margings specified in the marks E and G If the print data size is out of the printable area the printer should skip to next page TB74905 02F 1 02E 0705 Pr...

Reviews: