background image

                                                                          1                                                                          947776 

Back Box (Optional)

 

 

 

 

 

 

P-TEC VOICE PAGING SPEAKER

 

S-525A

 

Issue 1 

 

 

INTRODUCTION 

Clarity P-TEC Voice Paging Speakers are suitable for 
voice paging as well as background music. The S-525A 
is a 25/ 70 Volt model with adjustable taps and volume 
control.  P-TEC speakers consist of a 
3.6 inch cone speaker mounted in a unique surface-
mount baffle.  The baffle is designed for mounting on 
acoustic tile, such as those normally found in 
suspended-ceilings; and can be mounted without 
cutting large holes in the tile.  The mounting pins can 
be removed for mounting in a hard ceiling. The speaker 
housing has screw holes for securing speaker without 
mounting pins. Although the P-TEC speakers are 
designed especially for standard suspended ceilings, 
they can be used on many types of ceiling materials.   

P-TEC speakers are not  suitable for  use in 
plenum  ceiling environments. 

 

DIMENSIONS/WEIGHT 

 

•  8.00”Dia. x 2.50”D (20.32cm x 6.35cm) 

1.25 lbs. (.57 kg) 

 

INSTALLATION 

Selecting  the  Power-Tap  Wire 

 

1.   Remove the Quick-Connect connector from the 

accessory pack. 

2.   Select the desired power-tap wire:  
 

70V Watts 

25V Watts 

Lead Wire 

Common Common 

BLK 

.312 --  VIO 
.625 -- GRY 
1.25 -- BLU 

2.5 .312 WHT 
5.0 .625 GRY 

--Do 1.25 ORG 

--Not 2.5 RED 

--Use 5.0  BRN 

 

Note:   Refer to spacing chart (Figure 6) for  
recommended speaker spacing. 

 

 

 

 
 
 

 
 
 

 
 

 

 

 

Volume  Control 

 

 

F

i

gure 1. 25/70 Volt P-TEC Paging Speaker 

 

3

.   Install the Quick-Connect connector on the wire. 

Use pliers to close the connector over the wire. 
The connector can be removed by prying it open 
with a screwdriver, and can be reused several 
times (See Figure 2). 

 

 

 

 

 

 

 

 

 

 

 

Reusable 

Quick-Connect 

Connector 

 

Tap Wire 

 

 

Figure 2. Attaching the Reuseable Quick-Connect 

Connector 

Summary of Contents for S-525A

Page 1: ...uspended ceilings they can be used on many types of ceiling materials P TEC speakers are not suitable for use in plenum ceiling environments DIMENSIONS WEIGHT 8 00 Dia x 2 50 D 20 32cm x 6 35cm 1 25 lbs 57 kg INSTALLATION Selecting the Power Tap Wire 1 Remove the Quick Connect connector from the accessory pack 2 Select the desired power tap wire 70V Watts 25V Watts Lead Wire Common Common BLK 312 ...

Page 2: ...g tile and slide it out of the way 2 Install the speaker by inserting the mounting pins through the ceiling tile and hold the speaker in place 3 Place the wire and washers and speaker mounting clips over mounting pins so pins slide through clips To Amplifier Red Black Silver Figure 5 Maintaining Speaker Phasing Handling Shielded Speaker Cable If you are using shielded speaker cable splice the shie...

Page 3: ...6 25 WATT 26 24 22 20 16 15 14 12 10 8 SPL 78 50 WATT 24 22 20 16 15 14 12 10 8 SPL 80 1 0 WATT 24 22 20 16 15 14 12 10 8 SPL 83 2 0 WATT 24 22 20 16 15 14 12 10 8 SPL 86 4 0 WATT 24 22 20 16 15 14 12 10 8 MINIMUM MOUNTING HEIGHT 15 FT 10 FT 8 FT P TEC SPEAKERS ARE INTENDED FOR USE IN STANDARD 8 FOOT DROPPED CEILING TILE CEILING HEIGHTS OF MORE THAN 8 FEET OR HIGHER NOISE LEVELS MAY REQUIRE LESS T...

Page 4: ...major repairs will be subject to additional charges for parts and labor This Limited Warranty is in lieu of and excludes all other warranties expressed or implied and in no event shall Clarity be liable for any anticipated profits consequential damages loss of time or other losses incurred by the buyer in connection with the purchase operation maintenance installation removal or use of the product...

Reviews: