English
GREAT BRITAIN •
customer service
tel:
0845 300 9799
e-mail:
customerservice@clasohlson.co.uk
internet:
www.clasohlson.com/uk
7
6
5
4
3
2
1
Ver
. 20141015
Irrigation Timer
Art.no 31-8190
Please read the entire instruction manual before using the product
and then save it for future reference. We reserve the right for any
errors in text or images and any necessary changes made to
technical data. In the event of technical problems or other queries,
please contact our Customer Services.
Buttons and functions
6. Connect the timer to your tap using the ¾
″
tap connector or by
using the ½
″
-adaptor, if needed.
Note!
Do not tighten too hard,
as the coupling seals can be damaged by over tightening.
7. Connect the irrigation hose to the hose coupling (7).
Operating instructions
Note:
The timer is only designed to be used with cold water at
a max pressure of 6 bar (90 psi). If your water pressure is higher,
then a pressure regulator must be used together with the timer.
1. Set the [ FREQUENCY ] to the desired irrigation interval, from
once an hour to once a week.
2. Set the [ RUN TIME ] to the desired irrigation time, from 1 min to
120 min.
3. Turn on the tap.
Note:
Irrigation will start after the time
interval [ FREQUENCY ] you have set. So if you have set the
[ FREQUENCY ] to 1 hour then irrigation will begin one hour after
you input the setting and then irrigate once every hour thereafter.
4. If the [ RUN TIME ] setting is set to
ON
the water will be allowed
to flow constantly. If the [ RUN TIME ] setting is set to
OFF
the water will be shut off constantly.
Irrigation setup examples
• To set your watering settings to once a day:
Set the [ FREQUENCY ] setting to
24
.
• To set your watering settings to twice a day:
Set the [ FREQUENCY ] setting to
12
.
• To set your watering settings to every other day:
Set the [ FREQUENCY ] setting to
48
.
• To set your watering settings to once a week:
Set the [ FREQUENCY ] setting to
Week
.
Using the delay control to set the irrigation
start time
You can delay the irrigation start time in 1-hour intervals from
1 to 12 hours by depressing the irrigation control (4). Each press
corresponds to 1 hour of delay.
Example:
If you input your settings at 1:15 pm and you want your
irrigation to start at 3:15 pm then you would press the delay control
twice (1 press = 1 h delay).
Battery status indicator
Battery status (3) indications:
• Flashing: Functioning normally but the batteries are low and
should be changed as soon as possible.
• Solid: Batteries will soon become flat and water flow will be
shut off.
• Flashing-solid-off: Batteries are completely flat.
Note:
Inserting new batteries does not trigger the battery indicator
to activate or shine. The battery indicator only indicates low and
extremely low battery status, not when batteries are new or have
been completely flat for a time.
Care and maintenance
• Clean the timer using a lightly moistened cloth. Use only mild
cleaning agents, never solvents or corrosive chemicals. Keep all
water away from the battery chamber as water can leak in and
cause short circuiting.
• Never mix old and new batteries or rechargeable batteries with
non-rechargeable batteries.
• Never try to open the housing or modify the timer in any way.
This can lead to irreparable damage.
• Disconnect the timer from the tap and remove the batteries if
the timer is not to be used for an extended period.
Troubleshooting guide
The irrigation
timer does
not work.
•
Check the batteries and replace if
necessary.
•
Make sure the [ RUN TIME ] setting is not
set to
OFF
.
•
Make sure that the [ RUN TIME ] setting
is not the same as or greater than
the [ FREQUENCY ] setting, e.g. [ RUN TIME ]
set to 120 min and the [ FREQUENCY ]
setting is set to 2 hours.
•
Make sure the tap is open.
Disposal
This product should be disposed of in accordance with
local regulations. If you are unsure how to proceed, contact your
local council.
Specifications
Batteries
2 × AAA/LR03
Tap connectors
¾
″
and ½
″
adaptor
Irrigation time
1–120 min
Irrigation interval
1/hour up to 1/week
Size (L × W × H)
17 × 8 × 10.5 cm
Weight
255 g
1. ¾
″
tap coupling,
½
″
adaptor included
2. [ RUN TIME ]
Irrigation timer
3. Battery status indicator
4. Irrigation delay control
5. [ FREQUENCY ] Irrigation
interval settings
6. Battery cover
7. Irrigation hose
connection
Installation
1. Press the battery cover’s catch and remove the battery cover.
2. Carefully remove the battery holder and insert 2 × AAA/LR03
batteries. Note the polarity markings in the battery holder to
ensure correct battery insertion.
3. Carefully re-insert the battery holder back into the battery
compartment and refit the cover.
4. Check the timer’s operation by setting the [ RUN TIME ] setting
to
ON
. After a few seconds you should hear the mechanism
begin working to turn on the water flow.
5. After checking, turn the setting to the
OFF
position. You should
then hear the mechanism working to shut off the water flow.
