English
GREAT BRITAIN •
customer service
tel:
020 8247 9300
customerservice@clasohlson.co.uk
internet
www.clasohlson.co.uk
postal
10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
Ver
. 20180614
5
6
1
2
3
4
Battery-Powered Motion Sensor
Wall Light
Art.no 36-7333
Model S-1708B
Please read the entire instruction manual before using the product and then save
it for future reference. We reserve the right for any errors in text or images and any
necessary changes made to technical data. In the event of technical problems or
other queries, please contact our Customer Services.
Safety
• Do not locate the light close to heat sources, other lights or reflective surfaces.
• Avoid positioning the light close to obstructing tree branches.
• The motion sensor will not work if the light is installed behind glass
(e.g. indoors behind a window) or other translucent material.
Product description
Installation
Important:
For best results, install the wall light on a wall/vertical surface at a height of 1.8−2.1 m
above ground level.
1. Remove the locking screw (6) and the wall bracket.
2. Use the wall bracket as a template and mark out where you need to drill.
Before drilling and screwing, make sure that the wall is free from electrical
wiring and water pipes.
3. Screw the wall bracket to the wall. Use an appropriate fastening method for
the substrate material in question.
Batteries
The lid of the battery compartment is located underneath the wall bracket.
1. LED panel
2. Time switch control
3. Twilight switch control
4. Motion sensor
5. Wall bracket
6. Wall bracket locking screw
1. Release the catch and remove
the lid.
2. Insert 3 × AA/LR6 batteries. Follow
correct polarity with the positive
terminal of the middle battery
facing you and the positive
terminals of the batteries on either
side of it facing downwards.
Never mix old and new batteries.
Never mix rechargeable and non-
rechargeable batteries.
3. Refit the battery cover. Make sure
that the bottom edge is under
the tab and press the lid into place.
4. Mount the light onto the wall bracket
and secure it using the locking screw (6).
Instructions for use
2. Turn the twilight switch control (3) to set the level at which the light will be
activated at dusk.
- Turn the control clockwise towards the sun symbol for the light to be
activated even if it is still light outside.
- Turn the control anti-clockwise towards the moon symbol for the light to
be activated only when it is dark.
- Fine-tune the sensitivity to suit your needs.
3. Turn the time switch control (2) to adjust how long the light stays on for.
- Turn the control clockwise to increase the duration toward a maximum
operation time of approximately 7 minutes.
- Turn the control anti-clockwise to decrease the duration toward
the minimum operation time of approximately 3 seconds.
Care and maintenance
Clean the product using a lightly moistened cloth. Use only mild cleaning agents,
never solvents or corrosive chemicals.
Troubleshooting guide
The light does not work. • The batteries are flat. Change the batteries.
• Make sure that the battery compartment lid is
properly closed.
• Make sure that the batteries are inserted correctly.
Refer to point 2 of the
Batteries
section.
• Adjust the twilight switch sensitivity setting.
The light shines all
night.
Remove any sources of heat or reflective surfaces within
the detection zone. The light may need to be moved.
The light comes on for
no reason.
Take the batteries out to reset the motion sensor,
then put them back in again. Temporary sources of
heat or reflective surfaces within the detection zone
can activate the motion sensor.
The light is activated
during daylight hours.
Adjust the twilight switch sensitivity setting.
Responsible disposal
This symbol indicates that this product should not be disposed of
with general household waste. This applies throughout the entire EU.
In order to prevent any harm to the environment or health hazards
caused by incorrect waste disposal, the product must be handed in
for recycling so that the material can be disposed of in a responsible
manner. When recycling your product, take it to your local collection
facility or contact the place of purchase. They will ensure that
the product is disposed of in an environmentally sound manner.
Specifications
Batteries
3 × AA/LR6
Luminous flux
260 lm (+/- 10 %)
IP rating
IP44
1. You can twist both the LED light source and
the motion sensor into the desired position.
