Clayton TwoHAND Manual Download

Page: 1 / 12

800-248-8650 • www.VacuumSanding.com

5 in. (125 mm) and 6 in. (150 mm)

TwoHAND™ 12,000 RPM

RANDOM ORBITAL SANDER

MANUAL

Operator Instructions

Includes –Parts Page, Parts List, Please Read and Comply,

Proper Use of Tool, Work Stations, Putting the Tool Into Ser-

vice, Operating Instructions and Compressor Layout, Service

Tools and Accessories, Service Instructions, Back-Up Pads,

Specifications Table and Trouble Shooting Guide.

Declaration of Conformity

Clayton Associates, Inc. 1650 Oak Street Lakewood, NJ 08701 USA

declare on our sole responsibility that the products

5 in. (125 mm) and 6 in. (150 mm) TwoHAND™ Random Orbital Sanders (See Product “Specifications” Table for particular Model)

to which this declaration relates is in conformity with the following standard(s) or other normative document(s) EN ISO 15744:2008.

Following the provisions of 89/392/EEC as amended by 91/368/EEC & 93/44/EEC 93/68/EEC Directives and consolidating Directive

2006/42/EC

Place and date of issue

Name

Signature or equivalent marking of authorized person

Important

Read these instructions care-

fully before installing, operating,

servicing or repairing this tool.

Keep these instructions in a safe

accessible location.

Manufacturer/Supplier

Clayton Associates, Inc.

1650 Oak Street

Lakewood, NJ 08701 USA

TEL (800) 248-8650

www.VacuumSanding.com

Required Personal Safety Equipment

Recommended Airline

Size - Minimum

3/8 in

10 mm

Recommended Maximum

Hose Length

25 feet

8 meters

Air Pressure

Maximum Working Pressure 90 psig 6.2 bar

Recommended Minimum

Breathing Masks

Ear Protection

Safety Glasses

Safety Gloves

Lakewood, NJ 5/27/10

James E. Clayton

Original Instructions

Summary of Contents for TwoHAND











Search results

Summary of Contents for TwoHAND

Reviews:

Related manuals for TwoHAND

Brands by name

Popular brands

Clayton TwoHAND, Manual

Search results

Summary of Contents for TwoHAND

Reviews:

Related manuals for TwoHAND

Brands by name

Popular brands