background image

NOTICE TO PURCHASERS AND USERS OF OUR PRODUCTS 

AND THIS INFORMATIONAL MATERIAL 

 

The products described in this material, and the information relating to those 
products, is intended for knowledgeable, experienced users of abrasive blasting 
equipment. 
 
No representation is intended or made as to the suitability of the products 
described herein for any particular purpose of application. No representations 
are intended or made as to the efficiency, production rate, or the useful life of 
the products described herein. Any estimate regarding production rates or 
production finishes are the responsibility of the user and must be derived solely 
from the user’s experience and expertise, and must not be based on 
information in this material. 
 
The products described in this material may be combined by the user in a 
variety of ways for purposes determined solely by the user. No representations 
are intended or made as to the suitability or engineering balance of the 
combination of products determined by the user in his selection, nor as to the 
compliance with regulations or standard practice of such combinations of 
components or products. 
 
It is the responsibility of the knowledgeable, experienced users of the products 
mentioned in this material to familiarize themselves with the appropriate laws, 
regulations and safe practices that apply to these products, equipment that is 
connected to these products, and materials that may be used with these 
products. 
 
It is the responsibility of the user to insure that proper training of operators has 
been performed and a safe work environment is provided. 
 
Our company is proud to provide a variety of products to the abrasive blasting 
industry, and we have confidence that the professionals in our industry will 
utilize their knowledge and expertise in the safe efficient use of these products. 

MEDIA RECLAIMER/SEPARATOR 

 

 

 

 
 

Clemco Industries Corp.  

  One Cable Car Drive  

  Washington, MO 63090 

Phone: (636) 239-4300  

  Fax: (800) 726-7559 

Email: info

@

clemcoindustries.com 

www.clemcoindustries.com 

 

 

 

 
 
 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

OWNER’S MANUAL 

© 2005 CLEMCO INDUSTRIES CORP.  

 Stock No.: 23438 

 Manual No.: 2161-0202 

 Date of Issue: 02/27/02, Rev. E, 04/05

 

Summary of Contents for ZERO Blast Cabinets


















Reviews: