Clifford IntelliGuard 8000 Installation Manual Download

Page: 1 / 18

Standard Features of the IntelliGuard 8000

System Components

The IntelliGuard 8000 kit contains the following components:

One Prewired 24-pin Connector Harness

One PlainView 2 Coded Valet Switch

One Prewired 14-pin Connector Harness

One Medallion Siren

One IntelliGuard 8000 Control Unit

One Hardware Kit

One Digital Dual-Zone Proximity Sensor 4

One User’s Manual

Two Remote Transmitters

Two Window Decals

One Extended Range Receiver

One LED Status Indicator

In tel liGuard 8000/299

Lifetime Warranty

His & Hers Remote Controls

ACG™ 2 (Anti-CodeGrabbing™)

Extended Range Receiver

Audible Low-Battery Warning

Built-In Two-Point Immobilizer™

Optional Wireless Immobilizer™

Digital Dual-Zone Proximity Sensor 4

Optional Remotely Adjustable OmniSensor

Patented UltraSecure Coded Valet Mode™

Eight-Event TotalRecall™

Enhanced User-Selectable AutoArming

User-Selectable Remote Valet Mode Entry/Exit

Built-In BlackJax Anti-Carjacking System

Optional DataPort™ Interface and CliffNet Wizard

Pro™ Software

FACT — False Alarm Control and Test

Prewired LED, Sensor, Extended Range Receiver and

PlainView 2 Switch Connectors

High Output Medallion Siren

Dual-Mode “Chirp” Silencing

Remote Siren Silencing

Remote Door Locking/Unlocking with Built-in Relays

User-Selectable AutoLock

User-Selectable AutoUnLock

Integrated Electronic Timer

Turbo Timer Output

CliffNet DataPort Accessory Interface

Remote Keyless Entry and Accessory Activation Even in

Valet Mode

Remote Panic with Smart Locking/Unlocking

Smart Remote Trunk Release

Built-In Dual Parking Light Flasher with Onboard Relay

Remote-Controlled Courtesy Lighting

Patented Smart AutoTesting™

Patented Malfunction AutoBypass™ with

AutoReMonitoring

Patented Smart Prior Intrusion Attempt Alert

Patented Remote Control Code Learning and MultiRemote

Recognition

Clear All Remotes

Multiple-Car Control

High-Luminescence LED Status Indicator with Automatic

Battery-Saving Mode

Multiple Sensor/Trigger Inputs

Patented SmartPowerUp™ 2

Full-Time SecureAccess™ Programming

Advanced CMOS Microcomputer

Pre-Loomed Wiring

Three Auxilliary Outputs with Selectable Output Types

AutoActivation of Auxilliary Output C for Window

All-Close

Installer-Selectable Door Ajar/Delayed Courtesy Lights

Summary of Contents for IntelliGuard 8000



















Search results

Summary of Contents for IntelliGuard 8000

Reviews:

Related manuals for IntelliGuard 8000

Brands by name

Popular brands

Clifford IntelliGuard 8000, Installation Manual

Search results

Summary of Contents for IntelliGuard 8000

Reviews:

Related manuals for IntelliGuard 8000

Brands by name

Popular brands