GREAT BRITAIN • CUSTOMER SERVICE
tel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
Ver
. 20160526
Wireless Wall Switch,
2-gang
Art.no 36-6364
Model 50078
Please read the entire instruction manual before using the product and
then save it for future reference. We reserve the right for any errors in
text or images and any necessary changes made to technical data.
In the event of technical problems or other queries, please contact our
Customer Services.
Things to consider:
• Other wireless equipment using the same frequency band can
reduce the transmission range.
• The range of all wireless equipment depends on the type of
obstacles located between the transmitter and the receiver
(e.g. a concrete wall will interfere with the signal more than
a plasterboard wall).
If you experience problems, try the following:
• Turn off any other existing wireless equipment to check whether
this is the cause of the problem.
• Reposition the wireless equipment, shorten the distance between
the transmitter and the receiver or reduce the number of obstacles
(walls, furniture, etc.) between them.
Installation
5. Fasten the push buttons back
onto the switch module.
Care and maintenance
• Clean the exterior of the wall switch by wiping it with a damp cloth.
Use only mild cleaning agents, never solvents or corrosive chemicals.
• Remove the battery and store the wall switch out of reach of
children if it is not to be used for a long time.
Changing the battery
1. Remove the push buttons from the switch module.
2. Remove the old battery and insert a new one (1 × CR2032).
Insert the battery with the (+) facing you.
3. Refit the push buttons.
Troubleshooting guide
The wall switch
does not work.
• Check the battery and replace it if necessary.
• Is the wall switch paired with the receiver as
described above? Try pairing them again.
• Check that the device (e.g. light) which is
connected to the receiver is switched on and
not faulty.
• Is the wall switch too far from the receiver?
• Is the signal being blocked by furniture or
furnishings?
Responsible disposal
1. Remove the push
buttons and frame from
the switch module.
3. Remove the plastic tab
to activate the battery.
2. Mount the switch module in
the desired location using
the included screws.
Note:
It is
important that the switch is the right
way up, refer to the UP mark on
the switch.
4. Fasten the frame back
onto the switch module.
Align the notches in the frame with
the lugs on the mounting plate.
Operating instructions
Pairing the switch with a receiver
1. Make sure that the receiver that you are
going to use the wall switch with is ready
to be paired (refer to the user manual of
the receiver).
2. Switch the wall switch to [ ON ].
Operating a dimmer receiver
If the receiver you are using is dimmable, you can use the wall switch
to dim the light connected to the receiver. What to do:
1. Switch the light on by pressing [ ON ] on the wall switch.
2. Press [ ON ] on again to cause the light level to alternately increase
and decrease.
3. Press [ ON ] once again when the desired light level has been reached.
Deleting a receiver from the remote control
1. Make sure that the receiver that you wish to delete from the wall
switch is in the correct mode for removing devices (refer to
the manual of the receiver).
2. Switch the wall switch to [ OFF ].
This symbol indicates that this product should not be
disposed of with general household waste. This applies
throughout the entire EU. In order to prevent any
harm to the environment or health hazards caused by
incorrect waste disposal, the product must be handed
in for recycling so that the material can be disposed of
in a responsible manner. When recycling your product,
take it to your local collection facility or contact
the place of purchase. They will ensure that the product
is disposed of in an environmentally sound manner.
Specifications
Frequency
433.92 MHz
Range
25 m
Battery
1 × CR2032 (included)
