background image

860648849

Rev. A

Page 1 of 11

© 2018 CommScope, Inc. All Rights Reserved

Contents

Installation Instructions

FACT NG4 CHASSIS FOR MODULES & ADAPTER PACKS

TC-40161-IP-EN

Rev A, March 2019

www.commscope.com

1. 

General product information

The universal FACT NG4 chassis (FACT-xENG4) for modules & adapter packs supports the NG4-access connectivity 
packs and modules that easily snap in the chassis. It accommodates SC, LC and MPO adapter packs, MPO-modules 
(MPO to LC, or MPO to SC), Cabled modules (CMOD) and Value-added modules (VAM). 

2. 

Warnings and caution

•  Fiber optic cables may be damaged if bent or curved to a radius that is less than the recommended minimum 

bend radius. Always observe the recommended bend radius limit when installing fiber optic cables and patch 

cords.

•  Exposure to laser radiation can seriously damage the retina of the eye. Do not look into the ends of any optical 

fiber. Do not assume the laser power is turned off or that the fiber is disconnected at the other end. 

•  Pay attention to the routing of the patch cords. These should move/hang freely, where they leave the bend control. 

If you see that there is tension occuring on the patch cords, please reroute these. 

1. 

General product information ................................................ 1

2. 

Warnings and caution ............................................................ 1

3. 

Product image......................................................................... 2

4. 

Kit content ............................................................................... 2

5. 

Mounting FACT chassis in rack ............................................. 2

5.1. 

Mounting FACT chassis .............................................................................2

5.2. 

Dismounting FACT chassis ........................................................................2

6. 

Installation of the modules ................................................... 3

7. 

Routing the patch cords  (modules) ..................................... 5

8. 

Installation of the adapter packs...........................................7

9. 

Routing the patch cords (adapter packs) ............................ 9

10. Trademarks............................................................................11
11. 

Contact Information..............................................................11

Summary of Contents for FACT NG4












Reviews: