background image

I

NSTALLING

 

AN

 

E

XTERNAL

 C

ACHE

 

B

ATTERY

 (ECB)

About This Card

The HSZ70, the HSG80, the HSJ80, and the HSZ80 use the same 
ECB. This document contains instructions to replace an ECB in an 
HSZ70 HSOF Version 7.x Array Controller, an HSG80 ACS Version 
8.x Array Controller, an HSJ80 ACS Version 8.5J Array Controller, 
and an HSZ80 ACS Version 8.3 Array Controller.

NOTE:  

For instructions on upgrading a single-controller configuration to a 

dual-redundant controller configuration, see the appropriate 

DIGITAL 

StorageWorks

TM

 HSZ70 Array Controller HSOF Version7.x Service Manual

DIGITAL StorageWorks HSG80 Array Controller ACS Version 8.2 User Guide

,

 

Compaq

TM

 StorageWorks HSJ80 Array Controller ACS V8.5J Maintenance and 

Service Guide, Compaq StorageWorks HSG80 Array Controller ACS Version 8.x 
Maintenance and Service Guide

, or 

Compaq StorageWorks HSZ80 ACS Version 

8.3 Maintenance and Service Guide

.

General Information

The type of ECB used depends upon the controller enclosure type.

Figure 1 and Figure 2 provide general information about the cache 
modules used with many Compaq StorageWorks controller 
enclosures.

Figure 1.  Single ECB for single-controller configurations

TM

1

Battery disable switch

2

Status LED

3

ECB Y-cable

CXO5715B

CA

CH

E

PO

WE

R

STA

TU

S

SH

UT

 O

FF

1

3

~

2

European Union Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and 
the Low Voltage Directive (73/23 EEC) issued by the Commission of the European 
Community. Compliance with these directives implies conformity to the following 
European Norms (in brackets are the equivalent international standards):

EN 55022 (CISPR 22) 

Electromagnetic Interference

EN 50082-1 (IEC 801-2, IEC 801-3, IEC 801-4) 

Electromagnetic Immunity

EN 60950 (IEC 950) 

Product Safety

NOTICE

© 2000 Compaq Computer Corporation. Printed in the U.S.A.

COMPAQ, Compaq logo, and StorageWorks Reg. U.S. Pat. & Tm. Off. Windows NT is a 
trademark of Microsoft Corporation. All other product names mentioned herein may 
be trademarks or registered trademarks of their respective companies.

The information in this publication is subject to change without notice and is provided 
“AS IS” WITHOUT WARRANTY OF ANY KIND. THE ENTIRE RISK ARISING OUT OF THE 
USE OF THIS INFORMATION REMAINS WITH RECIPIENT. IN NO EVENT SHALL COMPAQ 
BE LIABLE FOR ANY DIRECT, CONSEQUENTIAL, INCIDENTIAL, SPECIAL, PUNITIVE OR 
OTHER DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITATION, DAMAGES FOR 
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR LOSS OF BUSINESS 
INFORMATION), EVEN IF COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES. THE FOREGOING SHALL APPLY REGARDLESS OF THE NEGLIGENCE OR 
OTHER FAULT OF EITHER PARTY AND REGARDLESS OF WHETHER SUCH LIABILITY 
SOUNDS IN CONTRACT, NEGLIGENCE, TORT, OR ANY OTHER THEORY OF LEGAL 
LIABILITY, AND NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY 
LIMITED REMEDY.

The limited warranties for Compaq products are exclusively set forth in the 
documentation accompanying such products. Nothing herein should be construed as 
constituting a further or additional warranty.

INSTALLING AN EXTERNAL CACHE BATTERY (ECB)

Second Edition (February 2000)
Part Number: EK–80ECB–IA. B01
Compaq Computer Corporation

Open Card Completely Before 
Beginning Installation Procedures

Summary of Contents for Storageworks ECB

Page 1: ...mity to the following European Norms in brackets are the equivalent international standards EN 55022 CISPR 22 Electromagnetic Interference EN 50082 1 IEC 801 2 IEC 801 3 IEC 801 4 Electromagnetic Immunity EN 60950 IEC 950 Product Safety NOTICE 2000 Compaq Computer Corporation Printed in the U S A COMPAQ Compaq logo and StorageWorks Reg U S Pat Tm Off Windows NT is a trademark of Microsoft Corporat...

Page 2: ...n replacing an ECB see Figure 5 match the vacant ECB bay with the cache module it supports This bay will always be next to the failed ECB Figure 5 Removing an ECB that supports cache module B in a Model 2200 enclosure 1 Battery disable switch 2 Status LED 3 ECB Y cable 4 Faceplate and controls for second battery 1 ECB charged LED 2 ECB charging LED 3 ECB fault LED CXO5713B CA CH E PO WER STATUS SH...

Page 3: ...n HSZ70 HSOF Version 7 x Dual Redundant Controller Use the following steps and Figure 1 or Figure 2 to replace an ECB 1 Connect a PC or terminal to the maintenance port of the controller with the operational ECB The controller connected to becomes this controller the controller for the ECB being removed becomes the other controller 2 Disable failover and take the controllers out of their dual redu...

Page 4: ...zel in the bay vacated by the current ECB Failure to reinstall the blank bezel might cause an overtemperature condition and damage the enclosure NOTE Install a Battery Service Label on the replacement ECB prior to installing it in the enclosure This label indicates the installation date MM YY for the replacement ECB b Install a Battery Service Label on the replacement ECB as described by the Compa...

Reviews: