background image

Installation Instructions  

AF60-12  

Required Crew: 3-4 Required 
Concrete: 12, 80 lb. bags  

Required Tools:  

● Wheelbarrow  
● Step Ladder (6’ or taller)  
● Shovel  
● Tape Measure  
● Digging Bar or Pick  
● Level  
● Allen Wrench (Provided)  
● Open end or Box Wrenches: 9/16”, ¾” 
● Hammer or Mallet  
● Ratchet Handle & Sockets: 9/16”, ¾” 
● Marker Pen  
● Drill: Cordless or electric, or impact driver  

 

Component Playgrounds is concerned about the safety of your vision. It 
is important that you choose to protect your vision by wearing proper 
safety glasses during each and every phase of this construction 
process.  

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING  

The AF60-12 can be installed as a one day project. The normal time 
required to install the AF60-12 is about 3-5 hours for a three to four man 
crew. This time requirement will vary dependent upon the composition of 
the soil and the speed of the installers. Mix and pour the concrete as the 
last step.  

*Before digging, please obey local laws by notifying your local 
underground utilities marking organization*  

 

Summary of Contents for AF60-12















Reviews: