Concept Z Performance 350Z Installation Manual Download | Manualshive

Page: 1 / 12

background image

Concept Z Performance 350Z & G35 Engine Oil Cooler Kit Installation Guide

Thank you for your purchase of the CZP oil cooler kit. Please make sure your kit came with all of the necessary
components listed below:

1x Setrab Oil Cooler Core

(19, 25 or 34 row core)

2x Setrab -10 AN to 22mm Port adapter fittings

(for cooler core to AN lines)

1x Mocal Sandwich Plate

(thermostatic or non-thermostatic)

2x Mocal -10AN to 1/2in BSP adapter fittings

(for the sandwich plate to AN lines)

2x Dowty Seal 1/2in BSP

(for Mocal sandwich plate fittings)

1x CZP Universal Oil Cooler Lower Bracket
1x CZP Z33/V35 Oil Cooler Upper Brackets

(long and short)

1x   CZP -10 AN SS Oil Cooler Line Long
1x   CZP -10 AN SS Oil Cooler Line Short
9x   M6x1.0x16mm Serrated-Flange Hex Head Bolts
7x   M6x1.0 Nylon-Insert Flange Locknuts
6x   M6 Weather-Resistant EPDM Rubber Washers
3x   M6x1.0 Plastic/Fiberglass Rivet Nuts
1x   M6x1.0 Rivet Nut tool

1

1
2
3
...
»

Summary of Contents for 350Z













Reviews:

No comments

Related manuals for 350Z

ANYWHERE CHARGER

Brand: I-GO Pages: 2

Epicure PN AFE36H3 Series

Brand: Dacor Pages: 8

Brand: Nokia Pages: 201

Brand: Nokia Pages: 22

Brand: Adam Hall Pages: 2

Brand: Audio Technica Pages: 22

Brand: Würth Pages: 21

Brand: Ganz Pages: 2

Brand: Spytec Pages: 25

Brand: Sphenic Technologies Inc. Pages: 4

Brand: Broan Pages: 24

Brand: GUTMANN Pages: 139

Brand: Xerall Pages: 6

Brand: ICON Pages: 9

Brand: ISOUND Pages: 1

Brand: Florence Pages: 6

Brand: AEM Pages: 7

Brand: Samsung Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands