Note: To winterize your ladder, remove it from the pool and drain water from stringers and treads.
Extension Kit for #6000 Ladder - Part #6000-EXT - Raises ladder to reach deck heights from 57” to
approximately 68”. Kit includes two extension boots, one additional ladder tread, hardware and instructions.
Order online at
www.conferladders.com
LIMITED, PRO-RATED WARRANTY
Confer Plastics, Inc. warrants their swimming pool ladders to be free from defects in
workmanship for one year from date of purchase. After the first year the cost to
replace a part is as follows:
MODELS #626B / #726
ALL OTHER MODELS:
2nd Year - 40%
2nd Year - 20%
3rd Year - 80%
3rd Year - 40%
4th Year - 60%
5th Year - 80%
Plus shipping/handling charges
DO NOT RETURN DEFECTIVE PART TO DEALER
The defective part should be returned, postpaid, to:
Confer Plastics, Inc.
97 Witmer Road
North Tonawanda
N.Y. 14120 U.S.A.
Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name,
address, and daytime phone number.You will be notified of cost to replace part.
This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
97 Witmer Road
North Tonawanda, New York 14120
Toll Free U.S. 800-635-3213
716-694-3100 / FAX 716-694-3102
www.conferladders.com
Printed in U.S.A.
MADE IN THE U.S.A. by:
SAFETY RULES
• Locate ladder on a solid base
• One person on the ladder at a time
• Ladder
MUST
be installed
per manufacturer’s instructions
• DANGER:
No Diving
or jumping from ladder
• Face ladder when entering and
leaving pool
• To prevent entrapment or drown-
ing, do not swim through, behind or
around ladder
• Ladder to be used as a swimming
pool ladder only
ASSEMBLY AND INSTALLATION MANUAL
CONFER PLASTICS, INC.
MODEL 6000
ADJUSTABLE HEAVY DUTY INPOOL LADDER
42" TO 56"
Step 11.
Step 12.
Drill a 1/8" pilot hole through
the handrail ends at the
pre-marked locations into
the stringers and repeat
this step for the adjustable
tubes and mounting blocks.
Place the ladder in the
desired position on the
deck and slide the
ladder assembly down
until the bottom tread
meets the pool liner.
Slide the adjustable
tubes with the mount-
ing blocks as needed
to position the ladder
correctly on the deck.
Make sure the
bottom tread is
flush with the
pool liner.
Ladder
Assembly.
Slide
adjustable
tubes to
position
against deck.
Dotted lines
represent pool edge.
Using a
cordless drill
attach the
mounting
blocks
with eight
#10 1-1/4"
screws.
Secure the handrail using four
#10 1-1/4" screws at the
pre-marked locations
(two per handrail).
Secure the handrail to the
tubes using four #10 1-1/4"
screws at the pre-marked
locations (two per handrail).
*DANGER:
Use a cordless drill for
assembly and installation. Use
extreme caution if using an electric
drill near water.
4
of current parts
list price
SAVE THESE INSTRUCTIONS
DEALER/INSTALLER: GIVE TO HOMEOWNER
As required by ANSI/NSPI - This ladder is equipped with an anti-entrapment barrier to prevent children from swimming behind
or through the rungs of the ladder. It is NOT intended as a substitute for proper adult supervision.
10a.
Please refer to the separate instruction sheet for anti-entrapment barrier installation.
CP-6000 09/04
OPTIONAL ACCESSORY
SKIM-IT
SKIMS OFF DEBRIS Cut cleaning time
75% with skimmer extension that guides debris directly
into your skimmer. Fits most in-ground and above-
ground pool skimmers. Corrosion-resistant plastic Skim-It
installs in seconds without tools.
Confer 6000_9_04 9/23/04 2:13 PM Page 1
