The Crestron® TS-7-MSMK and TS-10-MSMK multisurface mount kits provide a versatile flush
mount solution for Crestron TSS-7, TSS-10, TSW-760, and TSW-1060 touch screens. Using the
TS-7-MSMK or TS-10-MSMK, the touch screen may be mounted directly onto glass, granite,
marble, plaster, smooth stone and masonry, or almost any other flat surface.
The TS-7-MSMK and TS-10-MSMK rear housing provides four cutout holes (on the top, bottom,
and sides of the housing) for running concealed cables to the touch screen using the included
adhesive-backed raceway. A plastic cover with an opening for the raceway is attached to the
rear housing to conceal any unused cutouts.
NOTE:
For simplicity within this guide, the term “MSMK” is used to refer to both the TS-7-MSMK
and TS-10-MSMK except where noted.
Check the Box
Item
Qty
TS-7-MSMK or TS-10-MSMK
Coupler, Plastic (P/N 2049574)
2
Fitting, Plastic, Inside Corner (P/N 2049571)
1
Fitting, Plastic, Outside Corner (P/N 2049572)
1
Fitting, Plastic, Right Angle (P/N 2049573)
2
Raceway, PVC, 3 ft x 0.45 in. x 0.77 in. (P/N 2049567)
3
Screw, 4-40 x 3/8 in., Undercut Head, Phillips, Black (P/N 2007173)
4
TS-7-MSMK-B and TS-7-MSMK-W Only
Template, Overlay, Mounting Cap, TS-7-MSMK (P/N 4530137)
1
Template, Overlay, Mounting Housing, TS-7-MSMK (P/N 4530129)
1
TS-10-MSMK-B and TS-10-MSMK-W Only
Template, Overlay, Mounting Cap, TS-10-MSMK (P/N 4529858)
1
Template, Overlay, Mounting Housing, TS-10-MSMK (P/N 4530128)
1
TS-7-MSMK-B Only
Bracket, Plastic, with Adhesive, Black (P/N 4529616)
1
Cap, Plastic, with Adhesive, Black (P/N 4529618)
1
Cover, Plastic, with Detents, Black (P/N 2052978)
1
TS-7-MSMK-W Only
Bracket, Plastic, with Adhesive, White (P/N 4529615)
1
Cap, Plastic, with Adhesive, White (P/N 4529617)
1
Cover, Plastic, with Detents, White (P/N 2052977)
1
TS-10-MSMK-B Only
Bracket, Plastic, with Adhesive, Black (P/N 4529597)
1
Cap, Plastic, with Adhesive, Black (P/N 4529599)
1
Cover, Plastic, with Detents, Black (P/N 2052933)
1
TS-10-MSMK-W Only
Bracket, Plastic, with Adhesive, White (P/N 4529596)
1
Cap, Plastic, with Adhesive, White (P/N 4529598)
1
Cover, Plastic, with Detents, White (P/N 2052932)
1
Install the MSMK
The following is required for this installation: a level, a roll of masking tape, a Phillips
screwdriver, and a surface cleaning product that does not leave a film.
Use the following procedures to mount the MSMK onto a flat pane of glass or a similar smooth
surface (such as granite, marble, plaster, or smooth stone and masonry). The adhesive on the
MSMK mounting bracket attaches permanently to the surface.
Position the Rear Housing Template
An overlay template for the rear housing is provided with the MSMK to help ensure that it
remains level during installation.
NOTE:
The rear housing template included with the TS-7-MSMK has the same dimensions as a
TSS-7 or TSW-760, and the rear housing template included with the TS-10-MSMK has the same
dimensions as a TSS-10 or TSW-1060. The template can be used as a reference to help select
and mark a mounting location for the MSMK.
To attach the rear housing template:
1.
Clean and dry the mounting surface thoroughly.
2.
Select a mounting location for the MSMK and the raceway kit, and determine whether the
raceway will be entering the MSMK from the top, bottom, left, or right cutout.
3.
Use a level and masking tape to attach the included rear housing template to the surface
at the chosen location. Ensure that the template is level before proceeding.
Rear housing
template
Level
Mounting
surface
Install the Raceway Kit
The included raceway kit is designed to be installed on a nearby smooth surface to conceal
cables running to the touch screen from the floor, ceiling, or an adjacent wall, pillar, or mullion.
The raceway kit contains three cable channels, two flat elbows, one inside elbow, one outside
elbow, and two couplings.
The raceway may be painted after installation to match the walls or the surrounding decor.
CAUTION:
The raceway kit must be installed prior to installing the MSMK, and the location of
the raceway cannot be changed once the MSMK is installed. The raceway kit cannot be installed
on textured surfaces.
To install the raceway kit:
1.
Create a raceway cutout by removing the appropriate perforated strip from the rear
housing template. For example, if the raceway will enter the MSMK from the left side,
remove the left perforated strip from the template.
2.
Use a level and the reference line on the template that is perpendicular to the chosen
raceway cutout to tape a reference guide over the center cutout.
Use reference line
perpendicular to
raceway cutout to tape
a reference guide
Remove appropriate
perforated strip from
template to create
a raceway cutout
Reference line (4)
Raceway cutout
strip (4)
Level
3.
Use the template guides to cut the raceway to the required length. The end of the raceway
that will enter the MSMK can also be cut to a specific shape for a finished appearance.
4.
Route all necessary cables into the raceway. Press the sides of the raceway together to
snap it shut.
5.
Remove the protective liner from the rear of the raceway.
6.
Use the chosen raceway cutout in the template and the taped reference line to position
the raceway on the mounting surface. Ensure the raceway is level prior to adhesion.
CAUTION:
The end of the raceway must not extend beyond the taped reference line. The
rear housing will not install properly if the raceway extends beyond this line.
NOTE:
The included plastic cover can be used as a template to help ensure that the
raceway is level prior to adhesion.
Raceway
Raceway
cutout
Level
7.
Press the raceway firmly against the mounting surface until it adheres completely.
8.
Attach any elbows, couplings, and additional cable channels as necessary.
9.
Remove the taped reference guide from the surface and template.
TS-7-MSMK/TS-10-MSMK
Multisurface Mount Kits for TSS-7, TSS-10, TSW-760, and TSW-1060, Flat
