About the product
A Parking assist system uses ultrasonic sensors to monitor distances.It
electronically detects the area at the rear of your vehicle while
reversing, and alerts you with an audible tone/visual warning if there
is an obstacle behind your car.
This product features a self-test and learning function which is ideal
for cars with tow-bars, or with spare wheels located at the rear.
Each part of this product has passed rigorous testing before be-ing
released to the market and is reliable at a wide temperature range.
The unit is warranted for a limited period of time from the date of
purchase. In the unlikely event of a defect arising in this product
when used in accordance with the manufacturer's instructions, the
parts would be repaired or replaced free of charge.
Important notice
Disclaimer
The parking assist system is designed as a driver assistance device,
and should not be used as a substitute for safe parking practices.
You must constantly check the outside circumstance while parking.
The manufacturer does not guarantee or assume liability for collisions
or
damage caused
while parking your vehicle.
Parking sensors provide assistance while reversing. Driving skills,
such as slowing down, use of mirrors etc. are always essential.
1. This unit is for vehicles with 12V DC.
2. Unit should be installed by a professional auto technician.
3. Route wiring harness away from heat sources and electrical
components.
4. It is strongly recommended to check the position of the sensors
before the actual drilling of the holes.
5. Perform test after finishing the installation.
Manual
Parking assist
system
All rights reserved.
The right to change the design and specifications for improving the product is reserved.
CA-5014
MODEL:
Key features
Dual-color LED display with built-in buzzer
Intelligent detection, super for cars with spare tire or other protrusion
Anti-false alert technology
Self-test function
All weather design
Technical parameter:
Input voltage 9~16V DC
Beep volume 70 ~ 90 dB
Detection range 0.3m ~ 2.5m/1ft ~ 8.2ft
Sensor installation height 45cm ~ 60cm/1.5ft~2.1ft
LED display
Warning light & damaged
sensor location indication
A B C D
LED indicator
Buzzer
Learning function for car with tow bars or spare wheel
Switch ignition on, engage and disengage reverse gear 10 times.
On the 10th time stay in reverse gear for 6 seconds while the kit
performs the learning function.
To clear the learning function switch ignition on, engage and disengage
reverse gear 12 times. On the 12th time stay in reverse gear for 8
seconds while the kit reverts to factory settings.
X
10
+
1"
The display will flash and beep
once, this indicates that the
learning function is successful.
The system will no longer false
alarm because of a tow-bar or
spare wheel.
Flash and beep once
B e
Self-test function
B e
B e --- Be --- Be ---
When reverse gear is selected, the system will perform a self-test
procedure.
1.If no faults are detected after selftest, the buzzer will beep"once,
and the display will scan once.
2.If a faulty sensor is detected after selftest, the buzzer will beep
three times, and the display will show the faulty sensor location.
When the learning function is
activated, the system will ignore the
tow-bar or spare wheel and only detect
other objects behind the vehicle.
Note: If the vehicle does not have a tow-bar or spare wheel, you do not need to
use this function.
0.5 m/
1.64ft
Flash and beep once
beep three times
B e
In "0" position (Factory Setting)
In "20" position
Dual intelligent function for spare wheel
Sensor installation height choose
Sensor installation
55cm<H<65cm / 1.8ft<H<2.1ft
(Factory Setting)
Sensor installation
45cm<H<55cm / 1.5ft<H<1.8ft
0.50 m
1.6 ft
49cm/1.6ft
29cm/
0.95ft
In "0" position: The measured distance is between sensor and obstacle.
In "20" positon: The measured distance is between spare wheel (20
cm/0.65ft) and obstacle.
ECU
B e
B e
