background image

 
RS1-G5, RS3-G5, RS4-G5 
RS4-G5 FM 

(1-Way System) 

 

RS7-G5 FM 

(2-Way Paging System)

 

 

REMOTE START SYSTEM 

 
 

OPERATING INSTRUCTIONS 

 

 

CONGRATULATIONS

  on  your  choice  of  a  Cool  Start

™  Remote  Engine  Starter  and  Keyless  Entry  with  DP 

Technology by Crimestopper Security Products Inc. 

 This booklet contains the information necessary for operating 

your system.  If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. 

 
The RS1-G5, RS3-G5 & RS4-G5 system comes with (2) 1-way AM remotes 
The RS4-G5 FM system comes with (2) 1-way FM remotes

The RS7-G5 FM system comes with a 2-Way LCD Pager and a 1-Way FM remote.

 

 

OPTIONAL Features

 are to be connected only if desired or agreed upon by the customer and the installing dealer 

i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc.  These features may also require 
additional parts and/or labor fees.  Consult with your installer beforehand to be sure of what is going to be installed 
with your particular system. 
 

 

 
 
CRIMESTOPPER SECURITY PRODUCTS, INC. 
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 
 

REV   07-2014 

 

This  device  complies  with  FCC  Rules  part  15.  Operation  is 
subject to the following two conditions: 1) This device may not 
cause  interference,  and  (2)  this  device  must  accept  any 
interference that may be received, including interference that 
may  cause  undesired  operation.    The  manufacturer  is  not 
responsible  for  any  radio  or  TV  interference  caused  by 
unauthorized modification to this equipment. Such modification 
could void the user's authority to operate the equipment. 

 

 

Summary of Contents for Cool Start RS1-G5

























Reviews: