CrimeStopper CoolStart RS1905FM Installation Instructions Manual Download | Manualshive

Page: 1 / 32

background image

RS-1405DP/1505DP 1 WAY SYSTEMS

RS-1905FM 2-WAY SYSTEM

DP SERIES (Data port)

REMOTE ENGINE STARTING SYSTEM

INSTALLATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS

on your choice of a “Cool Start” System by Crimestopper Security Products Inc. This booklet

contains the information necessary for installing your remote starter system. If any questions arise, contact your
installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.

DISCLAIMER:
This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation.  To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation.  This book is provided as a GENERAL GUIDELINE and the
information contained herein may differ from your vehicle.  Crimestopper Security Products, Inc. and its’ vendors shall not
be liable for any accident resulting from the use of this product.  This system is designed to be professionally installed into
a vehicle in which all systems and associated components are in perfect working condition.

TECHNICAL SUPPORT: (800) 998-6880

Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: tech-support@crimestopper.com

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV A 08.2005

This device complies with FCC Rules part 15.  Operation is subject to
the following two conditions:  (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such  modification  could  void  the  user’s  authority  to  use  the
equipment.

1
2
3
...
»

Summary of Contents for CoolStart RS1905FM

































Reviews:

No comments

Related manuals for CoolStart RS1905FM

Brand: AV-GAD Pages: 2

Brand: Emerald Pages: 4

Brand: Cobra Pages: 28

Brand: Radio Shack Pages: 4

Brand: AEG Pages: 28

Brand: AEG Pages: 48

Brand: AEG Pages: 46

SRC 4331 CD/MP3

Brand: AEG Pages: 64

Brand: AEG Pages: 122

DIGITRADIO 50 SE

Brand: TechniSat Pages: 204

Brand: Giant Alarm System Pages: 3

Brand: CrimeStopper Pages: 23

Brand: Black Widow Security Pages: 8

Brand: Panther Pages: 20

Energy Clock Radio 300

Brand: ENERGY SISTEM Pages: 14

Brand: ADE Pages: 158

Brand: FAAST Pages: 12

Brand: Avital Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands