background image

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

2-Way FM Remote Start & Alarm System 

 
 

CONGRATULATIONS!

 on your choice of a CS-2013FM 

2-Way FM Paging Remote Alarm/Remote Starting System 

by Crimestopper Security Products Inc.  

This booklet contains the information necessary for installing, using, and 

maintaining your alarm system.  If any questions arise, contact your installation dealer first, or Crimestopper 
Security Products Inc. at the Tech Support number listed below.  This system is designed for single vehicle 
operation.  The Remote start functions of this system are designed for use with automatic equipped transmission, 
fuel injected vehicles only.  This system is compatible with diesel engines. 

 

*IMPORTANT INFORMATION: Primary and Optional Features

 

-PRIMARY:

  These are features that must be connected in order for the system to operate properly i.e. Siren, 

L.E.D., Power, Ground, Door pin, Hood pin (Remote Start Inhibit) etc. 

 

-OPTIONAL:

  These are features to be connected only if desired or agreed upon by the installing dealer (i.e. Door 

Locks, Starter Disable, Trunk, and Auxiliary Remote Output etc.) 

 

Note:  Additional labor and parts will be required for some features and on vehicles equipped with Factory Anti-
Theft Systems such as GM PassKey®/Passlock®/VATS, or Key-FOB based RF Transponder systems such as 
FORD P.A.T.S.®

 

 
 

TECHNICAL SUPPORT (800)-998-6880 
Monday - Friday 8:00am - 4:30pm Pacific Standard Time 
Website: www.crimestopper.com 
E-mail: email@crimestopper.com 

 

CRIMESTOPPER SECURITY PRODUCTS, INC. 
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 

This device complies with FCC Rules part 15. Operation is subject 
to the following two conditions:  (1) This device may not cause 
harmful interference, and (2) This device must accept any 
interference that may be received, including interference that may 
cause undesired operation. The manufacturer is not responsible 
for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modification could void the 
user’s authority to use the equipment. 

 

CS-2013FM

 
 
 

Summary of Contents for CS-2013FM



























Reviews: