RTX220 QR - Manual
DataPort
®
25 Secure Quick Start Guide
1. Installation Steps
1.1 Receiving Frame Installation
a. Slide the receiving frame into an open 3.5” Floppy Drive bay.
b. Secure the receiving frame to the chassis with the mounting screws provided.
c. Attach a SATA data cable to the JP4 connector on the rear of the frame and attach
the other end of the data cable to the appropriate SATA port on the computer’s
motherboard.
d. Attach a 4-pin Floppy power connector to the rear of the receiving frame.
1.2 Hard Drive Installation
a. If the carrier is bundled with a frame, press the Eject button once to release the
button, and again to eject the carrier from the frame.
b. Slide the cover of the carrier back and off.
c. Remove the screw kit from the carrier.
d. Insert a 2.5” SATA hard drive with the top label facing down into the unified power
and data connector inside the carrier.
e. Secure the hard drive to the carrier by
using the mounting screws provided.
f. Replace the cover and secure it by
inserting two screws from the screw kit
into the rear of the carrier.
Product Warranty
CRU-DataPort (CRU) warrants this product to be free of significant defects in material and workmanship for a period of five years from the original date of purchase.
CRU’s warranty is nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties. CRU expressly disclaims all other warranties, including but not limited to, the implied war-
ranties of merchantability and fitness for a particular purpose and non-infringement of third-party rights with respect to the documentation and hardware. No CRU
dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty. In no event will CRU or its suppliers be liable for any costs
of procurement of substitute products or services, lost profits, loss of information or data, computer malfunction, or any other special, indirect, consequential, or
incidental damages arising in any way out of the sale of, use of, or inability to use any CRU product or service, even if CRU has been advised of the possibility of such
damages. In no case shall CRU’s liability exceed the actual money paid for the products at issue. CRU reserves the right to make modifications and additions to this
product without notice or taking on additional liability.
FCC Compliance Statement:
“This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is operated in a home or commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
In the event that you experience Radio Frequency Interference, you should take the following steps to resolve the problem:
1)
Ensure that the case of your attached drive is grounded.
2)
Use a data cable with RFI reducing ferrites on each end.
3)
Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug.
4)
Reorient or relocate the receiving antenna.
A5-025-0014-1 Revision 1.2
Product name/code
DataPort 25 Secure
Interface Types & Speeds
SATA: up to 1.5 GB/s
Compatibility
2.5” SATA Hard Drives
Data Connectors
•
One (1) SATA connector
•
One (1) mini-USB Security Key connector
Encryption
128-bit AES (Advanced Encryption Standard) or 256-bit AES
128-bit and 256-bit encryption are not cross-compatible
Connector Insertion Rating
25,000+ Carrier-to-frame
Operating System
Requirements
•
Windows 7, Vista, or XP
•
Mac OS X
•
Linux distributions that support ATA133, SATA, and/or USB
Compliance
EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
FIPS: FIPS 140-2, FIPS PUB 197
Shipping Weight
2.00 Pounds (includes accessories)
Product Dimensions
Complete Assembly: 4.02” x 6.10” x 1.02” (102mm x 155mm x 26mm)
Removable Carrier: 3.11” x 5.24” x 1.02” (79mm x 133mm x 26mm)
Warranty
We don’t expect anything to go wrong with your CRU product. But if it does, Tech
Support is standing by and ready to help. Contact us at http://www.cru-dataport.com/
support. We also offer phone support at (800) 260-9800.
Visit http://www.cru-dataport.com/technical-support/product-manuals.php to download a copy of the
complete User Manual. Additional product information can be found at http://www.cru-dataport.com.
FOR HOME OR OFFICE USE
Models Covered:
DataPort 25 Secure with AES 128
DataPort 25 Secure with AES 256
